Hi, is there an available developer in my tri-state area of Minnesota, N. Dakota, or S. Dakota? Please call me if you are available for a project for hire. The developer should...
I'm trying to design a very low power sensor that takes readings using ADC and SPI 200 times a second. I'm a bit worried by the current EasyDMA uses (1.1mA). As far as I can...
Hi, I am working on a project where I want to make one nrf51288 chip as central hub and connect that to a android phone and other salve nrf51288 .
idea similar to this: ...
Hi,
I have a code programming the nRF51422 development board to write to a Sharp Memory 96x96 pixel LCD screen using SPI.
Currently the code writes two numbers and a...
I've modified the ble_app_uart example by adding GPIOTE so that the transmitter sends a character to the receiver when a GPIO pin is toggled. This part is working well.
...
Hi,
I am working on my hardware product having nRF-51422 chipset. I just came to know from forum post that
nRF-52 chips will get arduino IDE support as standalone. I want...
Hi!
I've been using PCA10028 for a long time and I had some bricking issues but I've managed to un-brick it with "nrfjprog --recover" and everything would work again. ...
Hi Team,
Nrf52840 DK acting as central and we trying to connect our peripheral device, we observed below logs with total duration of around 300ms.
Is there any way limit...
Hi forum,
I am working on nrf52832 using sdk15.0.0. using project ble_app_beacon.
In this project I am setting tx_power 0dbm,4dbm,-4dbm and -8dbm.while setting this tx_power...
Hi, Nordic
nRF52 as GZP Device, nRF24 as GZP Host
I know if nRF52 is range of nRF24, the pair will be worked.
I want to know what is the distance.
And if I use unencrypt...
Hi everyone,
I work on an custom board with the nrf52840, the SDK 15.2.0, the SoftDevice 140 6.1.0 and FreeRTOS.
My problem is that during a BLE transfert of a lot of...
Can I develop a software with MESH network support (1MBPS) and 16 Central links (CODED_PHY)?
All my tries is unfortunaly. But I dont give up.
Just guide me please and...
Hi, I have 2 nRF52840 D K but suddenly both are not showing on my PC. I have checked my data cable which is working fine on mobile and transferring data. I have also checked...
Hello,
I am evaluating the possibility to use ESB protocol on nRF52840 development kit. As far as I understood, for HW limitations, the maximum number of pipes in a star...
Hi all.
I want to increase number of sending packets in TI. I searched for the answer and I found answer wasn't for v7.2.0.
please give me a solution for v7.2.0 sdk ....
Hi
I want to receive data through UART RX interrupt.
--> A n interruption occurs to notify me w hen one character(byte) is received, and i store it to my memory buffer...
Hi everyone!
We're working with the processor nRF51422 with S210 softdevice and we've found an issue about the QDEC sample frequency. In fact, the minimum sample period by...
i have nRF52840 Dongle (PCA10059) and when i connected the dongle and opened nrf connect SDK application and tried to run BLE, then i am getting the following error. Kindly...
I am following the step to install my nRF52DK, but when I check it with "python3 nrf_sniffer_ble.py --extcap-interfaces", it has some error:
Could anyone help?
Hey!
I will post the whole code if necessary but for instance as I thought it would be a little glitch in my code, I tried to explain the basics of my problem for now: ...
ASSET TRACKER V2 Modem problems:
I have set up asset tracker V2 for nRF9160 and it sends the messages (GPS, Temp, Hum, etc) and the corresponding timestamps, which I can...
