Hi, is there an available developer in my tri-state area of Minnesota, N. Dakota, or S. Dakota? Please call me if you are available for a project for hire. The developer should...
I'm trying to design a very low power sensor that takes readings using ADC and SPI 200 times a second. I'm a bit worried by the current EasyDMA uses (1.1mA). As far as I can...
Hi, I am working on a project where I want to make one nrf51288 chip as central hub and connect that to a android phone and other salve nrf51288 .
idea similar to this: ...
Hi,
I have a code programming the nRF51422 development board to write to a Sharp Memory 96x96 pixel LCD screen using SPI.
Currently the code writes two numbers and a...
I've modified the ble_app_uart example by adding GPIOTE so that the transmitter sends a character to the receiver when a GPIO pin is toggled. This part is working well.
...
Hi,
I am working on my hardware product having nRF-51422 chipset. I just came to know from forum post that
nRF-52 chips will get arduino IDE support as standalone. I want...
Hi!
I've been using PCA10028 for a long time and I had some bricking issues but I've managed to un-brick it with "nrfjprog --recover" and everything would work again. ...
I followed the "Getting Started Assistant" and can import and build the nRF9160 side.
SES -> Open nRF Connect SDK Project:
Works, "Build Solution" works, all seems...
nrfutil version 2.3.0 correctly fails with message " Application file not found." but incorrectly sets the return code to 0
nrfutil settings generate --family NRF52 --application...
I know it basic question but i need direct answer with numbers(exact voltage accuracy)
and i am very much confused to understand about adc output calculation please help...
Hello,
I'm attempting to enter System OFF mode via sleep_mode_enter() using a long press. However, I want to wake up from System OFF using that same button. The problem...
Hi to everyone,
I am having trouble establishing a network connection with NRF9160 Dk. I use a local SIM and according to the information I got from the provider, there...
Hi Nordic
I am using mesh sdk4.1 LPN example to develop a LPN product, we seems found that LPN's RF range will degrade large compared to common mesh node.
We want to try...
hello Nordic
i am working with nrf52840, sdk16, over the peripheral app_ble_blinky example
my system will go to sleep mode for 10 minutes each time, i wonder if there...
SDK: 4.1.0
Hi, I want to send change notification. so I writes below this.
Some buf_id has got failure in zb_zcl_ias_zone_set_status.
So I added loop which get...
Hi,
We are working on a board with nrf5340. We are running the nrf5340 in normal voltage mode. So, we have connected the VDD lines to 3.3V. Since we are using USB signals...
how can I put nrf52832 in the system on sleep mode on advertising timeout?
Currently, on timeout, the device is going in system off mode and restarting on interrupt.
Hello,
I noticed that you improved the hardware design in version 1.4. Is it still neccessary to use a bias tee for an external GPS? https://devzone.nordicsemi.com/f/nordic...
Hello, I am still learning about BLE devices and have a quick question regarding the Generic Access Profile. I understand that GAP defines 2 things:
The discoverability...
Per the notes on https://www.nordicsemi.com/Software-and-tools/Development-Kits/nRF9160-DK/Download#supl-c - "Highlight: Updated library made to work with the new modem library...
nRF52832 SDK 17.2
We are trying to get the packet loss/error information on a per channel basis. It is similar to what is being discussed in https://devzone.nordicsemi.com...
