I'm trying to design a very low power sensor that takes readings using ADC and SPI 200 times a second. I'm a bit worried by the current EasyDMA uses (1.1mA). As far as I can...
Hi, I am working on a project where I want to make one nrf51288 chip as central hub and connect that to a android phone and other salve nrf51288 .
idea similar to this: ...
Hi,
I have a code programming the nRF51422 development board to write to a Sharp Memory 96x96 pixel LCD screen using SPI.
Currently the code writes two numbers and a...
I've modified the ble_app_uart example by adding GPIOTE so that the transmitter sends a character to the receiver when a GPIO pin is toggled. This part is working well.
...
Hi,
I am working on my hardware product having nRF-51422 chipset. I just came to know from forum post that
nRF-52 chips will get arduino IDE support as standalone. I want...
Hi!
I've been using PCA10028 for a long time and I had some bricking issues but I've managed to un-brick it with "nrfjprog --recover" and everything would work again. ...
I want to build nrftoolbox app in android studio. I downloaded the zip file from the github website and also the required dfu library. I unzipped both the files in a folder...
Hi there,
I am implementing the SAADC example into my application whereby I should be able to sample all 8 ADC channels "simultaneously" at a relatively high frequency...
I am trying to change the radio Tx power in nRF5340. I'm using Zephyr HCI RPMsg for the network core. The datasheet says it should support up to 3dBm. However, the Zephyr...
In the soft device documentation (html) the message sequence diagram for Btle Stack Enable calls sd_ble_cfg_set twice with the same set of parameters. Is this a mistake? The...
Hi All,
I am developing a custom BLE profile for my current project and several of my characteristics are write/notify characteristics. I am finding that when I write...
Hi there,
I just started using Embedded Studio (v5.10d on Windows 10, nRF Connect SDK version 1.4) with nRF52840dongle and nRF5340 PDK. Here is what I did
1. Copied...
Hi, I am developing a new project in which I will use NRF52810. I read in the datasheet that it is possible to configure NRF52810 in LDO and DC / DC regulators mode. My application...
Hello:
Looking at the different demos (applications and samples) available for nRF9160, I noticed that some of them generate multiple hex files while others, only few...
Hi,
I have bootloader programmed in nrf52840. Using OTA I programmed one application region but that application stuck after bootup.
Now how to recover from this situation...
Hi,
I have an existing application built on top of the ble_att_mtu_throughput example. I want to send log data over a BLE connection, and I am trying to use the CLI over...
Hello, guys!
We are using nRF52840 with SDK 17.2. In our system, there is a need to configure nRf52840 as SPI slave device and connect it to some other MCU. Naturally, our...
Hello,
I had a problem with the nordic uart service peripheral. We are using an nRF51822 and the S130 software stack. I had a problem with the app_timer.c STATIC_ASSERT...
Hello guys,
I am facing the following problem:
I created a project from zero, using the Nordic Package for SeggerStudios
--> I selected the option A C/C++ executable...
Hi,
Tried enabling POF on while using S140 with the following code:
The board VDD and VDDH are configured to be 3.3V and in the lab, were dropping the voltage to...
getting error in running bootloader
Output/secure_bootloader_ble_s112_pca10040e Release/Obj/nrf_dfu_validation.o: in function `nrf_dfu_validation_init':
