Suppose there are 10 BLE peripherals in a room and one BLE Central,then is there any way i can get the list of available peripherals[name or id.. etc]?
I am using NRF5182...
I am using SDK_11 s130 on nrf51-dk. When err_code is any value other than NRF_SUCCESS, APP_ERROR_CHECK(err_code) will cause nRF51-dk board to reset. How can one get APP_ERROR_CHECK...
Hello All,
I have problem with ble_app_uart which are not support DFU services.
When I am implement both services device will not advertise. and when ble_nus uninitialized...
[symptom]
I want to update my application/bootloader/softdevice by DFU.
Steps are shown below.
bootloder/softdevice update
if 1 step is done, application update...
Dear Developer Zone,
I am new to ANT and am looking for someone to help me to setup an example 15 channel (14 devices) ANT network using the S332 soft-device to test communication...
Hello,
i am working with the Enhanced ShockBurst proprietary protocol and i am wondering where I can find the sources of this protocol, so that I can do some changes. ...
[uart - Copy.rar](/a master _error.png ttachment/3cc01f5e2484d2b0f33e62befd3e6a62)
hello there
I am interfacing master nrf51 dk with nxp's slave lpc11u24
(1) my main...
hello Nordic
i work with nrf52832 as dispersed units and an nrf52840 dongle/ BL654 Laired which also has the nrf52840 as the central unit.
stage 1 - i need to transfer...
Hi,
Looking at the differences between S132 and S140 SoftDevice, I see there's lack of support for Long Range (Coded PHY) on the S132 (and S112 for that matter), which is...
Hello,
I am using the Thingy:91 PCB and I have disabled the nRF52 by cutting SB4 and soldering SB3. This makes me unable to log through UART. For this reason I implemented...
To the kind attention of Nordic support team,
I need to disable, enable gzll more times. When enabling it, code gets often stuck in my case as in figure: nrf_impala.c 442...
I have achieved Bluetooth connection between 1*ble_central<------>6*ble_peripheral.
But, ble_peripheral sometimes upload data at the same time, then sometimes lose data...
We're successfully using nrf_crypto_aead_crypt() with AES CCM, a 128-bit key, a 64-bit MAC, and the NRF_CRYPTO_ENCRYPT operator to encrypt some data and generate a MAC that...
HI, all,
I am trying to transfer my previous project from nrf51822 to nrf52840, and at very the beginning ,I can not make the UART/UARTE of nrf52840 work.
0, I have programmed...
Hi, everyone,
I am pretty new to nRF52 development. Right now, I have an issue with the SAADC trigger by RTC, which I follow this example . The issue that I have right now...
Hey all,
Here's another question. Many of the examples in the Nordic Connect SDK are rather large. Transferring them with MCUmgr at 115200 BAUD takes sometimes more than...
Hi
I am testing sending and receiving data between nRF51 dongle and peripheral by example of heart-rate-collector.
now I could find characteristics I need(write, read...
Hi all,
My application is as follows:
I have an android app which will send some data to a nRF DK. The data I want to send is in HEX characters between 0x00 to 0xFF. And...
Hello,
For nRF51822 and nRF52832, I'm using GPIOTE, PPI and timers to measure the duration that a pin, which is normally low, goes hi (typically 100-300 milliseconds). I...
The following questions are in regards to the instructions at nRF_Connect_SDK-modifying-a-sample-application .
In the Windows environment, I am transitioning from using...
