Hi, is there an available developer in my tri-state area of Minnesota, N. Dakota, or S. Dakota? Please call me if you are available for a project for hire. The developer should...
I'm trying to design a very low power sensor that takes readings using ADC and SPI 200 times a second. I'm a bit worried by the current EasyDMA uses (1.1mA). As far as I can...
Hi, I am working on a project where I want to make one nrf51288 chip as central hub and connect that to a android phone and other salve nrf51288 .
idea similar to this: ...
Hi,
I have a code programming the nRF51422 development board to write to a Sharp Memory 96x96 pixel LCD screen using SPI.
Currently the code writes two numbers and a...
I've modified the ble_app_uart example by adding GPIOTE so that the transmitter sends a character to the receiver when a GPIO pin is toggled. This part is working well.
...
Hi,
I am working on my hardware product having nRF-51422 chipset. I just came to know from forum post that
nRF-52 chips will get arduino IDE support as standalone. I want...
Hi!
I've been using PCA10028 for a long time and I had some bricking issues but I've managed to un-brick it with "nrfjprog --recover" and everything would work again. ...
As unicast address is a address of a element in a node.
We have to assign unicast address to 500 nodes each contains 2 elements, and we configured publish and subscribe...
Hello,
I am using nrf52832, having SDK 15.3.0 in Segger Studio IDE. Win10
I am using fds_test_find_and_delete() function, to find and delete particular record from flash...
I latest firmware and loaded and software thingy91_ltem_v0.2.2.hex. And I get reboot all the time. It was working when I first got the kit then when I was testing this weekend...
Firstly, I am a very beginner in the BLE domain. I have very little knowledge of it.
I want to do a project where multiple BLE peripheral devices(nRF52) will communicate...
Hello:
I have questions about eSIM card.
As we know, GSMA standard eSIM card is an empty chip, we can use eSIM card after ISP information is installed into eSIM card....
Hello,
I have the same question as mentioned in this article:
https://devzone.nordicsemi.com/f/nordic-q-a/19252/how-to-avoid-interrupt-handling-is-not-missed-with-sd_app_evt_wait...
Hi,
I use nrf sniffer to monitor BLE communication. After pairing with encryption, wireshark indicates Encrypted packet decrypted incorrectly (bad MIC).
I think there...
I configured Uart on 23 - Rx and 24 - Tx of NRF52832.
In simple uart example it works fine with uart_event_handle for rx.
But when this code is merged with Nrf Mesh Dimmer...
Hi,
Having gone through the nRF52832 datasheet, the only discernible drawbacks of moving from an external crystal to synthesizing the Low frequency clock from the high-frequency...
On the Nordic Semiconductor infocenter , 12 reference designs for the nRF52840 are given, 6 for the big QIAA chip and 6 for the small CKAA chip. However the reference designs...
Hi
We are developing the use of ESB together with BLE, using the Timeslot API.
We have been using the known tutorial for the ESB timeslot implementation:
https://devzone...
Hi,
We are using nRF52832(lairdBL652) module for indoor application for the prototype version.
We are using nrf52832 for both central and Beacon device.
We have made...
Hi,
I have combined the light switch and the dimming example. The thingy 52 contains one generic onoff server and two generic level server for brightness and colour.
The...
I updated Thingy91 with modem firmware (mfwnrf9160100.zip) and application firmware (thingy91_ltem_v0.2.2.hex) from latest firmware package (thingy91fwv022.zip).
Question...
Hi,
I have nRF9160 DK. I downloaded nRFConnect SDK with source code.
I know that samples compiled with libraries are loaded and executed under MCU on the DK board. Since...
