I'm trying to design a very low power sensor that takes readings using ADC and SPI 200 times a second. I'm a bit worried by the current EasyDMA uses (1.1mA). As far as I can...
Hi, I am working on a project where I want to make one nrf51288 chip as central hub and connect that to a android phone and other salve nrf51288 .
idea similar to this: ...
Hi,
I have a code programming the nRF51422 development board to write to a Sharp Memory 96x96 pixel LCD screen using SPI.
Currently the code writes two numbers and a...
I've modified the ble_app_uart example by adding GPIOTE so that the transmitter sends a character to the receiver when a GPIO pin is toggled. This part is working well.
...
Hi,
I am working on my hardware product having nRF-51422 chipset. I just came to know from forum post that
nRF-52 chips will get arduino IDE support as standalone. I want...
Hi!
I've been using PCA10028 for a long time and I had some bricking issues but I've managed to un-brick it with "nrfjprog --recover" and everything would work again. ...
I want to build nrftoolbox app in android studio. I downloaded the zip file from the github website and also the required dfu library. I unzipped both the files in a folder...
On page 143 of the datasheet the following is written, "The input buffer of a GPIO pin can be disconnected from the pin to enable power savings when the pin is not used as...
how to configure S112 for maximum throught put just like ATT_MTU Throughput Example available for other soft device. I tried everything on nRF52810 using S112 and the max...
Hi, I am using PTS 7.0 for Bluetooth profiles testing. The DUT is connected to PC (with Ubuntu and Android AOSP system installed). The Android PTS test instruction indicates...
Hi,
I am having some problems with nrfutil. I encountered the following errors when trying to generate a key. Similar issue was seen when trying to generate a zip file....
Hi,
I have a code word well in nRF52832 used twis1.I transplant it from nRF52832 to 52810.First I enabled twis0,Second, change NRF_DRV_TWIS_INSTANCE to twis0.Then I can...
Hello!
nRF52832, SDK15, SES
I'm working on a project where DFU is activated by receiving a command from the app. I took ble_app_buttonless_dfu as reference.
For starters...
Hi,
I am using SDK14.2, s132, with nRF Connect on Android.
I have used my own implementation of the CTS_C BLE service. The chip is able to detect, and request the...
Nordic Semiconductor-ites and fellow forum members have yet to steer me wrong so here we go.
My product has 52832 on both sides. The central and its 21col x 2 row LCD display...
Hello,
I am developing an application with SDK 15.2 on my nRF52840 development board (pca10056) and want to run it on my nRF52840 dongle (pca10059). I have hit a problem...
We have been comparing the current consumption of the nRF52 running FreeRTOS Tickless Idle versus a constant tick and using the idle task to sleep and the results are interesting...
Hi,
Does the pc_ble_driver_py contain any API for paring or bonding bluetooth devices? And if so, do you have any examples or documentation which explain how to use them...
Hi,
Is there a way to reject a buttonless DFU attempt (nRF52832, SDK14.2) ?
I want my application to allow DFU only when certain conditions are met.
I thought using...
Hi,
Can anybody clear me on the maximum and minimum connection interval with some good example. I have not understood the connection intervals clearly.
Regards,
An...
I am working on a BT mesh network where nodes are mostly sleeping (to conserve power) when they wake up, they need to send a sensor reading to another node (which is always...
It is unclear for me why the following code look like this (conn_ble_gap_sec_keys.c, SDK15):
Is it logical that here the SER_MAX_ADV_DATA is used? is there actual advertising...
