Hello,
I am writing an iOS code using Swift3 to connect an iOS10 device to nRF52 pca10040 and blink an LED. The nRFConnect on iOS can easily connect using the device name...
void in_pin_handler (nrf_drv_gpiote_pin_t pin, nrf_gpiote_polarity_t action)
{
nrf_drv_gpiote_out_toggle(PIN_OUT);
}
This function work with interupt event (push...
here I have a very strange problem. I m trying to send the data(1 byte) from slave to master,and I have to use the multilink demo because I will have 2 slave devices.
The...
I'd like to erase all the pages managed by FDS as part of a "Hard Reset" operation. fds.c has a hint of a "FRESH_INSTALL" directive (part of an enum defined in fds_internal_defs...
nrf51822
SDK v10
SD S110 v8
hello!
My pj is about ANCS+nus+hid mouse sevices.
If my borad had bonded with an iPhone,then download new hex from mdk ,and run.
...
Hello.
I would like to develop FW for the nRF52832, using Eclipse IDE + ARM GCC + Segger JLink OB.
I've seen on the segger webpage that the nRF52832 is a Cortex M4 processor...
When using app_timer through scheduler, a break and go will overflow the event queue if a timer is a repeat timer. The effect is that it's not possible to debug.
To work...
Hello,
This is less a question and more of a survey. We've recently completed development on a project using the nRF51822 but have run into an odd power problem. We built...
hello,
i am using the nrf52840 preview devkit and am currently trying to find a solution for timestamping / for a time-base. the idea was to use the RTC for that since...
i know that it's not up to you guys to tell me this but maybe you can give me a hint: right now i'm using the bluetooth developer studio together with the nordic plugin for...
Hi there.
I recently migrated from SDK 13 to SDK 14.0.0 and followed the migration guide in detail. I've found that when I try to advertise, ble_advertising_start() will...
According to the nRF52810 datasheet,the reference circuitry with DC/DC regulator setup connet the pin DCC and the pin DEC4. Then how much is the voltage output of the pin...
I am using SEGGER Studio on MacOSx.
When use the latest mesh SDK, I can run the light_control example and see the debug log in the Debug Terminal of SEGGER Studio.
However...
Hi
I am trying BLE multirole application ble_app_multirole_lesc from the SDK 13.0.0.
I am using nRf52832 DK along with GCC toolchain.
For debugging I am using Segger...
In the mesh network, the sender uses trickle algorithm to control the repeat sending process, and at last the sender will send the message forever in a max interval at a handle...
Hi Nordic Team!
After developing our firmware on the nRF52 HDK, we designed our custom board, and we're starting to write our custom board configuration file.
The main...
Hi,
we've developed a custom board with nrf51 and use bonding and white listing.
Everything works fine when connecting and bonding iOS phones with this devices but with...
HEllo,
I was wondering whether or not is advisable to use the same handler to handle transmission/reception of data over SPI0 and SPI1 interfaces.
I have two sensors...
Hello
I am using a custom board, based on nRF52832 CIAAB0. I have also S132 installed, and I am using SDK 13.1.0. TWI pins are P0.16 - SCL & P0.18 - SDA. The code is based...
I am trying to advertise some data using the s130 softdevice to my MS49SF2 (nrf51822 based module ) and then flashed the hrs example code to it..
Still I couldn't find...
hi, Nordic
I'm using your nRF51-DK(PCA10028) board, on android, i disconnect connection by call BluetoothGatt.disconnect ( developer.android.com/.../BluetoothGatt.html ,...
