Hi, I am working on a project where I want to make one nrf51288 chip as central hub and connect that to a android phone and other salve nrf51288 .
idea similar to this: ...
Hi,
I have a code programming the nRF51422 development board to write to a Sharp Memory 96x96 pixel LCD screen using SPI.
Currently the code writes two numbers and a...
I've modified the ble_app_uart example by adding GPIOTE so that the transmitter sends a character to the receiver when a GPIO pin is toggled. This part is working well.
...
Hi,
I am working on my hardware product having nRF-51422 chipset. I just came to know from forum post that
nRF-52 chips will get arduino IDE support as standalone. I want...
Hi!
I've been using PCA10028 for a long time and I had some bricking issues but I've managed to un-brick it with "nrfjprog --recover" and everything would work again. ...
I want to build nrftoolbox app in android studio. I downloaded the zip file from the github website and also the required dfu library. I unzipped both the files in a folder...
Hello,
I have a device based on nRF51822 revision 2 and SoftDevice S110 v7.1.0. Because it is revision 2 it is affected by PAN44 and PAN45, and by default the SoftDevice...
Hi,
We are seeing issues with Segger Systemview Post Mortem Mode. Original issues were revealed on our custom board with SDK 2.6.1. After enabling the feature firmware crashes...
Hello,
I would like to test TX for ltem. I'm using nrf9160. I would like to use: - Band: 1 - Frequency: 1950 MHz - Tx power: 23 dBm - Bandwidth: 5 MHz - Modulation: QPSK...
Hello,
I've recently was checking out the Zigbee Weather Station application running on the Thingy53 and have spotted a weirdly formatted log message regarding temperature...
Hello everyone, recently I received a thingy:91x with an extra truphone sim card.
I am based in Indonesia and want to test the cellular connection from device but doesn...
I built the demo zephyr/samples/bluetooth/hci_usb for my nrf52820, and it worked well.
But when I tried to read its manufacturer name by using command `hciconfig -a`, it...
Hi there,
I want to capture all the logs made by Zephyr and printk() calls. I want to forward these logs via USB using our custom application protocol for debugging purposes...
Hello folks,
I need some help troubleshooting a BLE antenna issue on our custom nRF52840 PCB . Any insights would be greatly appreciated!
Issue:
BLE sometimes advertises...
ncs v2.9.0
nRF52832 DK (NUS central)
nRF52840 DK (NUS peripheral)
1) When connected, see the empty PDU from peripheral to central about 100ms interval.
2) To use...
I'm trying to add an Aquara temperatur sensor to Zigbee shell running as coordinator on a 58233DK.
Regarding the logs in the serial terminal, it looks like the network was...
Hi,
I am using a nRF9161-dk with the nRF7002-ek shield WiFi tracking.
Using the nRF Connect Quick-Start, I downloaded the nRF Cloud Multi-service application and went...
I'm new to Nordic technologies and ML MCUs!
Does the ARM Cortex-M33 core, nRF5340 audio DK devkit, without any other board od periferic, support edge impulse ML? If so...
NCS 2.7.0 nrf52840
I noticed in i2c_nrfx_twim.c there are some calls to pm_device_runtime_get, while in another thread ( thread ) it was mentioned that Nordic is no longer...
NCS 2.9.0
nRF52840-DK
Using the OpenThread CLI example.
After turning on the TCAT function, when using MeshCoP Commissioning, the joiner will experience a system failure...
Hi, we have a NPM1300 chip connected as I2C slave to a nrf5340, acting as I2C master. Everything works fine, but there is a small detail in the NPM user manual that I would...
