Currently we are considering whether we should use external Flash Memory or NRF52 Internal Flash.
External Flash memory has a lot of drawback in comparsion with internal...
Suppose there are 10 BLE peripherals in a room and one BLE Central,then is there any way i can get the list of available peripherals[name or id.. etc]?
I am using NRF5182...
I am using SDK_11 s130 on nrf51-dk. When err_code is any value other than NRF_SUCCESS, APP_ERROR_CHECK(err_code) will cause nRF51-dk board to reset. How can one get APP_ERROR_CHECK...
Hello All,
I have problem with ble_app_uart which are not support DFU services.
When I am implement both services device will not advertise. and when ble_nus uninitialized...
[symptom]
I want to update my application/bootloader/softdevice by DFU.
Steps are shown below.
bootloder/softdevice update
if 1 step is done, application update...
Dear Developer Zone,
I am new to ANT and am looking for someone to help me to setup an example 15 channel (14 devices) ANT network using the S332 soft-device to test communication...
Hello,
i am working with the Enhanced ShockBurst proprietary protocol and i am wondering where I can find the sources of this protocol, so that I can do some changes. ...
Hello,
I have setup a development environment using Eclipse and GCC. This setup works nicely. Thanks!
devzone.nordicsemi.com/.../
I noticed different examples in...
Hello,
We are currently designing the hardware for a production run of our product using the nrf52832 chip and would still like to have debugging capabilities with breakpoints...
I have been learning GCC+ Make work flow to build and debug nRF51822 S110-only applications based on the examples from NRF51 SDK v10.0.0. I started with ble_app_beacon example...
I tried to work application.
But firmware stops at advertising_init(). When I exchange advertising_init() and services_init(), firmware does not stop.
why ?
S110 v8.0...
Hello,
My device is nRF51822 SD110 8.0.0.
The problem occured after firmware update in bootloader (own, not SDK) with readback protection enabled.
So bootloader connects...
Hello,
I am currently finishing my deploy script and I am currently using nrfjprog to write some custom UICR data. I have a contiguous region of memory to write but I do...
Dear Nordic team,
Beside other persistent issues with your proprietary DTM command for setting Tx Power (see here and here ) I've found that default Tx Power in ble_dtm...
How do I add multiple devices to a whitelist (as the central, adding peripherals), then use the white list for multiple connections? I have read both
devzone.nordicsemi...
I have nrf51822 QFACA1 and STM32f407VG. I'm programming nrf51822 QFACA1 using STM32f407VG SWD pings. And now I want programming BLE nrf51822 QFACA1 but I can't find any working...
I bought MOD-nRF8001 BLE Module for prototyping. I gave 3.3v Supply to modules's 3.3V pin & GND to GND pin. But, I cant figure out weather mODULE IS ON OR OFF. Its unrecoverable...
Hiiii
In our industrial product we are using nrf24l01+ on PCB which will be going to fully coat with epoxy material while manufacturing. My question is that , whether this...
I have modified the ble_app_hrs_c_s130_pca10031 example to run without external RTC and collect only battery status data from BLE peripherals that have a service with UUID...
Hello,
I tried the example ble_app_multilink_central (SDK 11.0) with S130 soft device. My requirement is that nrf-dongle should work in central mode and it should connect...
Super general question :)
Our current products use nRF24 chips (paired with 8bit AVR's) and we're very happy with performance.
For us the key requirements are low latency...
Hi all, i am trying to load this example on the smart beacon kit; i followed this guide step by step ( devzone.nordicsemi.com/.../) but the problem is the if i load the precompiled...
