I'm trying to design a very low power sensor that takes readings using ADC and SPI 200 times a second. I'm a bit worried by the current EasyDMA uses (1.1mA). As far as I can...
Hi, I am working on a project where I want to make one nrf51288 chip as central hub and connect that to a android phone and other salve nrf51288 .
idea similar to this: ...
Hi,
I have a code programming the nRF51422 development board to write to a Sharp Memory 96x96 pixel LCD screen using SPI.
Currently the code writes two numbers and a...
I've modified the ble_app_uart example by adding GPIOTE so that the transmitter sends a character to the receiver when a GPIO pin is toggled. This part is working well. ...
Hi,
I am working on my hardware product having nRF-51422 chipset. I just came to know from forum post that
nRF-52 chips will get arduino IDE support as standalone. I want...
Hi!
I've been using PCA10028 for a long time and I had some bricking issues but I've managed to un-brick it with "nrfjprog --recover" and everything would work again. ...
I want to build nrftoolbox app in android studio. I downloaded the zip file from the github website and also the required dfu library. I unzipped both the files in a folder...
I am currently working on LE Audio broadcasting. The system operates successfully on 1M PHY, but I would like to use it to function on CODED PHY as well.
Both the receiver...
We use the https://api.nrfcloud.com/v1#tag/IP-Devices/operation/OnboardDevices endpoint to create and onboard new devices.
Recently, with no changes to code or certificates...
Some questions during the development of a DF project using the nRF52833DK:
Will excessive serial output affect the performance of the microcontroller? For example,...
Hello,
On my custom board, after upgrading from NCS version 2.5.1 to 2.6.1, BLE stopped working.
I get immediately the following trace after calling bt_enable(NULL)
...
I'm migrating from ncs v2.3.0 to ncs 2.6.1 in order to have the ram retetion working with the mcu boot.
But after some modification on my board file using a nrf5340 I get...
I have a custom board file which is based on nrf9160, I want to use it using the west build command and later flash it. I tried the steps under this tutorial: Nordic academy...
Just upgraded to NRF v 2.6.0 (Mac OS; VS Code). Our code previous built and ran successfully on our custom board with v 2.5.0 of the SDK.
Now we get the following error...
Hi all,
I'm developing a project on top of nRF5340. Thus I created a custom board definition in my project area:
That is a direct copy of ncs/zephyr/boards/arm/nrf5340dk_nrf5340...
Hello,
we are trying to use the nRF9160 as a serial modem for a Raspberry Pi running on Debian.
The application is basically the nRF sample "nrf\samples\cellular\modem_shell...
Hi,
I'm trying to build the Serial LTE Modem in my nrf9160 SIP custom board to communicate the STM32 MCU with the nrf9160 using AT Commands via uart.
My physical connections...
Hi,
I created a custom service in accordance with NUS service. I am able to assign all handles, subscribe to notifications. But I am not able to read any data from the device...
Based on my understanding on SPI signal, CS/SS pin need to pull down to low when read/write and pull up high when the action is finished.
May I know if this feature has...
I'm currently working on a project that uses the MLX90640 IR sensor. By default, this device has an I2C address of 0x33, but it can be set up with one of 127 different I2C...
Sifting through previous posts about redirecting printf to uart by using retarget.c, I have found this will work on previous versions of segger (5.42). Has anyone gotten it...
I tried adding the following settings to prj.config
CONFIG_CHIP_OTA_REQUESTOR=n
CONFIG_CHIP_QSPI_NOR=n
I've also tried to modify the Devicetree to be the qspi part in...