Dear Developer Zone,
I am new to ANT and am looking for someone to help me to setup an example 15 channel (14 devices) ANT network using the S332 soft-device to test communication...
Hello,
i am working with the Enhanced ShockBurst proprietary protocol and i am wondering where I can find the sources of this protocol, so that I can do some changes. ...
[uart - Copy.rar](/a master _error.png ttachment/3cc01f5e2484d2b0f33e62befd3e6a62)
hello there
I am interfacing master nrf51 dk with nxp's slave lpc11u24
(1) my main...
It is good practice to prefix the includes from one's C libraries with a directory so that they are all part of the same 'include namespace'. Unfortunately the Nordic SDK...
Hi, is there an available developer in my tri-state area of Minnesota, N. Dakota, or S. Dakota? Please call me if you are available for a project for hire. The developer should...
I'm trying to design a very low power sensor that takes readings using ADC and SPI 200 times a second. I'm a bit worried by the current EasyDMA uses (1.1mA). As far as I can...
looking at https://github.com/nrfconnect/sdk-nrf/tree/main/lib/location
specifically https://github.com/nrfconnect/sdk-nrf/blob/main/lib/location/cloud_service/cloud_service...
Hi, I am working on a project using the nRF52832 and the nRF5 SDK 17.1.0. We have a sensor with non linear behaviour and in our attempt to linearize it we found an article...
Hi,
I encountered a very strange issue. I need to control a device using GPIO. What I use is p0.22/p0.02/p0.03/p1.11/p0.31/p0.30. I modify the app.overlay file and check...
I'm running the SDK 17 radio test example on two custom board using nRF52833. My goal is to do a range measurement under ble_1Mbit mode.
My parameter as follows:
After...
Hi，
I am following the nRF Connect SDK Fundamentals course of Lesson 1 – nRF Connect SDK Introduction of Exercise 1 to install NCS development environment,when I executed...
When I tried to use PPK II to measure the alarm current of a smoke alarm product, I found that its test results were very different from those of the power analyzer. I didn...
Hi, I have a question regarding the nRF power management APIs. I'm trying to implement power management in my code, and I found that the pm_device_action_run() API can be...
Errata 36 for the nRF9161 (and the same problem exists on the nRF9151) disables the access port in SYSTEM ON IDLE, which is the default low power state for nRF9120 devices...
Hi,
My nrf9160-DK version is PCA10090, 1.1.3, 2023.31
I am trying to test the esim, but the firmware tells me no simcard found. After doublechecking the esim soldering...
Hello,
On T-Mobile's website [1] there are some documents relating to their certification requirements [2]. In their FAQ they state that they have minimum band requirements...
Hello, we are planning to evaluate several type of AoA algorithm, and we have ISP1907-AOA-DK kit from Insight-SiP Is there any guideline you know to get IQ data from each...
Hello, Im in the middle of a custom board bringup and I am attempting to get Bluetooth GATT server working. I have tested the bluetooth code using the nrf5340dk board files...
Hi,
I'm using nrf5340 audio dk board. I configured UART0 with the help of nrf connect fundamental course - Link and I started transmitting the data in UART. But after sometime...
Dear team,
I am trying to build my CPP project with Nordic Zephyr SDK. I am using following commands:
west build --build-dir nrf_build -b nrf52840dk_nrf52840 sample -DZEPHYR_TOOLCHAIN_VARIANT...
