Hi
We are developing software for the nRF51 with Keil under VirtualBox. Previously we used the PCA10000 dongle with the Master Emulator and MCP without issue. Now, with...
We are using nRF51822 for our products.
We want to know the min value of "Receiver sensitivity" when we use this chip for BLE.
The Datasheet says "Receiver sensitivity...
Dear
The BLE Multi-link example (ble_app_multilink_central and ble_app_multilink_peripheral)
shows how one central device can connect to multiple peripheral devices. ...
In the MCP app, if I have the following service data for an Eddystone beacon:
0x10, // Eddystone-URL type
0x00, // TX power in dBm. This is a signed integer so 0xEE ...
I have the nRF Control Panel Android application. It works fine with several BLE devices, but specifically for the Fitbit Flex, it fails to connect.
I know Fitbit wristbandes...
Hi,
The situation:
I was able to successfully receive known packets from a device running gzp_device_dynamic_pairing, from, the host running the gzp_host_dynamic_pairing...
Hi everyone
nrf51822,softdevice s130 2.0.0
now i used softdevice s130 establish two connection as a central with two s110 peripheral device,at the same time i establish...
Hi,
Initially, I can send and receive AT commands. But after sending the power-down commands
sequence from "Getting Started with nRF93M1 DK v0.4"
I could not receive...
I've trying to get MCUBOOT woth work with my project & after much time/effort & found my project, untoughed, works on the nrf52840DK. I then discovered that the mcuboot build...
Hello,
Thank you for your help.my questions are as follows
SDK : ncs 3.4.0
Hardware board ：nRF54L15
Based on the ncs SDK 3.4.0, how should one set the MAC address...
Hi! We have recently upgraded nRF Connect SDK. Since this change, some of our users experience issues with uart - two nRF52840 communicating together. We have not been able...
On a custom Zigbee End Device application for the Thingy:53 (NCS v2.9.3), ZCL Configure Reporting commands sent by Zigbee2MQTT are rejected with ZCL status FAILURE for almost...
Hello,
I am working on a project based on the Nordic nRF54L15 microcontroller, using nRF Connect SDK and Zephyr RTOS. The application handles BLE communication in both advertising...
Environment : - nRF Connect SDK v3.4.0. - CONFIG_SPI_NRFX_SPIM_RTIO=y. - SPI_HOLD_ON_CS is not enabled. The same completion ordering is present in upstream Zephyr main : https...
Hello,
We run a small fleet of battery-powered nRF9151 devices (Thingy:91 X) on modem firmware mfw_nrf91x1_2.0.4 and nRF Connect SDK v3.1.1. The modem regularly asserts...
Hi Nordic Team,
Does the reset of 54L15 need to be handled? Still pull up a 1k resistor. Also, do I need two wires for debugging?
The customer has another question....
Hi, this is a bit of a vague question. I am not exactly looking for an answer, i was just wondering if anyone had a similar experience.
I am using nrd5340-dk and my application...
Hi all,
Quick question on NFC design practice.
I am using the nRF54L15 NFC in tag emulator mode (differential), with the following setup:
Antenna: Molex 1462360051...
We have transitioned over to using memfault OTA platform and used release overrides for some devices.
Is there a way to easily search for devices that have release overrides...
Hi everyone! I'm having difficulties in setting up a little project in which I want to pass I2S data over USB. I know I'm using the old USB Audio Class endpoints, but everything...
I am using nRF Connect SDK 3.4.1 on three nRF54L15 devices:
A ───────── B ───────── C
A–B: A central / CS initiator
B peripheral / CS reflector
B–C: B central / CS initiator...
