I want to build nrftoolbox app in android studio. I downloaded the zip file from the github website and also the required dfu library. I unzipped both the files in a folder...
Hello,
I have a device based on nRF51822 revision 2 and SoftDevice S110 v7.1.0. Because it is revision 2 it is affected by PAN44 and PAN45, and by default the SoftDevice...
Hi Guys,
I know this is more for software issues. But I was curious as to where I can find trusted case providers/makers for the nrf51822 Beacon. Can anyone from the community...
Hi,
Has anyone converted the Adafruit graphics library for Arduino, Adafruit_GFX.h, to be compatible with the nRF51?
Could you please advise on how to convert this Arduino...
Hi all,
I have a few questions:
How is that ADC's common mode rejection capabilities? Rejection for 60 Hz interference, etc...
The datasheet has "typical...
Hi all !
I'm trying to evaluate the throughput i can have between a Motorola 4G and the nrf51. The nRF51 is the peripheral and the phone is acting as a central.
To do...
Hello !
I can see nrfutil is written in python and have a lot of dependencies and functionalities what typically need for x86 based host.
A lot of discussions about porting...
Hi everyone.
I would like to know if there is any good nrf mesh communication libraries for desktop applications (preferably C#)?
I would like to develop some desktop...
Hi experts,
I have a problem with programming NRF5340 SoC when using the NRF-Programmer tool. About our board, we use PCBA instead of NRF5340 Dev-Kit.
Step1: My coworker...
I'm moving an application from NCS v2.0.2 to NCS v2.1.0
Everything compiles properly in v2.0.2.
I think I've converted all of the pin definitions properly from the v2...
Hello,
we are using nRF9160 as Bluetooth host together with the Mcumgr Gatt service. We would like to be able to perform FMFU update using the Mcumgr library. We have verified...
Hi:
After downloading the sdk, I installed the compilation environment on my laptop and successfully compiled the at_client project. However, after the same installation...
I want to implement a sophisticated peripheral that implements a keyboard, mouse, and raw HID interface via USB and BLE.
I haven't found composite HID examples for USB or...
Hi,
When I try to build the ESPI sample using west I'm getting the following error:
Can you please let me know what the error is? I tried looking up the issue, but couldn...
Hello Nordic Team,
While going through this page on peripherals used by Softdevice https://infocenter.nordicsemi.com/topic/sds_s140/SDS/s1xx/sd_resource_reqs/hw_block_interrupt_vector...
Hi guys,
I want to send 'a' characters via the uart1 of the nRF52840-DK. I cut the short on the SB6 jumper to disconnect LED 2 from P0.14, which also happens to be TX of...
Hi DevZone
I just want to ask if one can use the nPM1100 with the unregulated output to the nRF9160 (which can take 3-5.5V), and the regulated output the other peripherals...
We try to get audio samples form analog or digital MEMS microphone to nrf54840 RAM memory with low power consumpion at 32kHz rate. We consider to use internal SAADC, PDM or...
hi, I want to use PPI function for timer trigger GPIOTE,
when timer interrupt comes, my output pin will toggle, but I find my code doesn't work, I think it is GPIOTE mistake...
I am trying to run the nrf/samples/bluetooth/peripheral_lbs example for the nRF5340-Audio-DK using nRF SDK v2.1.0. I am using the following command to run the example:
west...
We have a product on the market that uses the nRF24 and a PIC, chosen primarily for it's cost and rapid development time. We are now looking into using a nRF52 to replace...
