Hi,
Has anyone converted the Adafruit graphics library for Arduino, Adafruit_GFX.h, to be compatible with the nRF51?
Could you please advise on how to convert this Arduino...
Hi all,
I have a few questions:
How is that ADC's common mode rejection capabilities? Rejection for 60 Hz interference, etc...
The datasheet has "typical...
Hi all !
I'm trying to evaluate the throughput i can have between a Motorola 4G and the nrf51. The nRF51 is the peripheral and the phone is acting as a central.
To do...
I have a digital microphone chip, it has the CLK, DATA, LR_SEL three pins, now I will pick up the three pin nrf5283 three pin is as follows: CLK connectionI2S_CONFIG_SCK_PIN...
Hello, Nordic Team, I'm embedded designer from Russia, discovered your amazing wireless MCU NRF52832. I looked through your SDK and peripheral drivers, and unfortunately found...
Thanks Stefan. The zip file making and updating steps work perfectly for me, if I follow your steps and make it from your stock pre-built "dfu_test_app_hrm_s132.hex". My question...
What is the reason Nordic dont want to provide yet dual mode solution - BR/EDR + BLE? - There are plenty of legacy BT devices on the market and the new BLE devices doesnt...
I am working on developing an application for nRF52833 DK (PCA10100) using nRF5 SDK_v17.1 and nRF_802.15.4 Radio driver v1.6. I am using the s122 Soft device on the device...
Hi all,
So I was following this guide for updating my firmware over BLE: https://devzone.nordicsemi.com/guides/nrf-connect-sdk-guides/b/software/posts/ncs-dfu#dfu_over_bluetooth...
Mesh SDK 5.0, SoftDevice S140 v7.2.0, NRF52840, SEGGER ------------------------------------------------------------------------------------ Hello, My problem is that I can...
When i open the Toolchain on my mac it loads and put upp a crash page. i have already: restarted my mac, reintstalled and restarted but i get the same crash
The System...
Hi, I currently have a project with an nRF52832 chip using SDK 14.2, I would like to upgrade the project and change the chip to nRF5340. Is there a way to migrate the project...
Are there any examples showing use of the MQTT library using Bluetooth as the Link Layer? I see this on Zephyr's repo zephyr/subsys/net/l2/bluetooth at main · zephyrproject...
Here is a warning I get linking an application that uses nRF DM library 5/14] Linking C static library app\libapp.a [6/14] Linking C executable zephyr\zephyr_pre0.elf c:/toolchains...
Hi,
Can any one list what are the reasons for sd_ble_gap_connect returns NRF_ERROR_DATA_SIZE?
In ble_gap.h NRF_ERROR_DATA_SIZE error code doesn't exist for sd_ble_gap_connect...
Hello,
We have already product with BLE 4 and now we are moving to BLE5. As per the example code we have updated our code to BLE 5 but we are not seeing advertisement...
Purpose: to develop a central device using nRF5340 and to enable both BLE Mesh and AoA features.
Questions:
1. nRF5 SDK supports nRF51 and nRF52 series but not for nRF5340...
Hello,
We were middle way during the development when we found out that we had a higher packet loss than what is acceptable.
So we start to analyze this issue.
Scenario...
Hi,
I reviewed the PCA10121 schematic for using SPI4 pins to connect to Semtech SX1262. Since SPI4 bus also connected to SD card and DSP. I checked to see if SPI0..3 pins...
In my application, we regularly transmit a stream of notifications from a Peripheral Server to a Central Client. The general strategy for this is to enqueue a packet, and...
