I'm trying to design a very low power sensor that takes readings using ADC and SPI 200 times a second. I'm a bit worried by the current EasyDMA uses (1.1mA). As far as I can...
Hi, I am working on a project where I want to make one nrf51288 chip as central hub and connect that to a android phone and other salve nrf51288 .
idea similar to this: ...
Hi,
I have a code programming the nRF51422 development board to write to a Sharp Memory 96x96 pixel LCD screen using SPI.
Currently the code writes two numbers and a...
I've modified the ble_app_uart example by adding GPIOTE so that the transmitter sends a character to the receiver when a GPIO pin is toggled. This part is working well.
...
Hi,
I am working on my hardware product having nRF-51422 chipset. I just came to know from forum post that
nRF-52 chips will get arduino IDE support as standalone. I want...
Hi!
I've been using PCA10028 for a long time and I had some bricking issues but I've managed to un-brick it with "nrfjprog --recover" and everything would work again. ...
I want to build nrftoolbox app in android studio. I downloaded the zip file from the github website and also the required dfu library. I unzipped both the files in a folder...
Hello,
We would like to use BLE to transmit a lossy data stream at high data rate. Looks like Isochronous channel is the best choice. How's the Isochronous channel is...
Hello
We need to scan for more than 8 devices, so we can't use witelist directly.
We have an idea to use presaved IRK and mac-addresses and use scanning without witelist...
Hi,
I work on an AOA projet and i have a problem.
I have already made a transmitter (with an nRF52833) and a receiver (also nRF52833) and i can see the CTE send by my...
I need to add a custom BLE service with over 20 custom characteristics. During the gap nitialization step, I set the BLE security mode and security level like this:
sec_mode...
Hi ,
Am following the below link https://devzone.nordicsemi.com/f/nordic-q-a/83402/ncs1-8-0-52840-mcuboot-spi-external-flash-can-t-build-pass ,
am able to build it for...
hello,
i am using nrf52832 with accelarometer i want to put my board in shutdown for current consumption for that i am giving this command sd_power_system_off(); whenever...
I need to be able to change the device name the SoftDevice uses AFTER the soft device is up and running. To change the device name, To do this I use
errorCode = sd_ble_gap_device_name_set...
Hi,
I currently have a macro in the nRF Connect Mobile app (Android) that displays RSSI every time I receive a temperature signal. I am saving the logged temperature and...
It seems that not all UICR registers are erased on this nRF52840 chip
nrfjprog -f nrf52 --recover
Just make sure one more time:
nrfjprog -f nrf52 --eraseuicr
nrfjprog...
Hi,
I am using nRF Connect SDK 1.9.1. Need to configure 2 UARTS one for debug messages and the other to connect with host CPU. Please help me with the following:
1. Can...
Dear support
I am developing my application based on central_multilink example and have a few questions:
1. in call back function connected() , I wonder why conn_connecting...
Hi,
I am trying to perform the read characteristic values from the nRF52840 DK to Android studio (Java) to a TextView. I have looked at the Android Blinky example but in...
Hello,
I am using an nRF52840 as a central BLE gateway with nRF connect SDK 1.8.0. I was looking for software changes to increase the scanning range. So far I've found the...
I am getting data on my Azure cloud using asset tracker code
I am enable to find tag as you can see from the Image , there was tag before sensor data , for example
before...
Hello Team,
I have a custom board based on nRF52833 platform.
I have used ble_app_uart application from S132(PCA10040) SDK
Is that okie to use S132 for nRF52833...
