Hi, is there an available developer in my tri-state area of Minnesota, N. Dakota, or S. Dakota? Please call me if you are available for a project for hire. The developer should...
I'm trying to design a very low power sensor that takes readings using ADC and SPI 200 times a second. I'm a bit worried by the current EasyDMA uses (1.1mA). As far as I can...
Hi, I am working on a project where I want to make one nrf51288 chip as central hub and connect that to a android phone and other salve nrf51288 .
idea similar to this: ...
Hi,
I have a code programming the nRF51422 development board to write to a Sharp Memory 96x96 pixel LCD screen using SPI.
Currently the code writes two numbers and a...
I've modified the ble_app_uart example by adding GPIOTE so that the transmitter sends a character to the receiver when a GPIO pin is toggled. This part is working well.
...
Hi,
I am working on my hardware product having nRF-51422 chipset. I just came to know from forum post that
nRF-52 chips will get arduino IDE support as standalone. I want...
Hi!
I've been using PCA10028 for a long time and I had some bricking issues but I've managed to un-brick it with "nrfjprog --recover" and everything would work again. ...
Hi, I am quite new to App development with Android Studio. My project is to make an app plotting the data collected from one of the pins of ItsyBitsy nRF52840. I found an...
I have just configured Wireshark 3.6.5 with nRF Sniffer 4.1.0 on the PC with Windows10, but I am not able to select column "Destination" to be shown. It is not present on...
I want my device to continuously advertise and if there is no advertising in between, at that time device should be in sleep mode, I've used idle_state_handle(); but still...
The default Kconfig option for the MCUBoot swap algorithm is CONFIG_BOOT_SWAP_USING_MOVE, which corresponds to:
https://developer.nordicsemi.com/nRF_Connect_SDK/doc/latest...
Hello,
I'm on the development of a biomedical application using nrf52832 module. Would like to know if the CPU core can be able to isolate itself (ignore all incoming interrupts...
I have watched your distance measurement webinar.
We want to use the distance measurement tool in our thread network, but I do not know how the synchronisation should be...
Peripheral: nRF52832
IDE: SES
SDK: nRF5 17.0.2
Hi,
I am attempting to jump from a non-BLE application to a BLE application. I was successful in modifying the "secure_bootloader...
Hi，
I have a question of my "PCA10056 boad", The VDD_NRF voltage is only 1.7V when connect microUSB of J2, I think one of my board components is broken, can you gei me some...
Hi,
I'm using nRF52805 with LIS2DW, accelerometer.
LIS2DW is controlled by I2C protocol. but I do not use nrf I2C driver. I am using two GPIO port emulating I2C. It works...
Hi,
Regarding QSPI, could I use the QSPI feature to fetch stored sensor data directly from the flash and send it via Bluetooth module, or is it only to increase the application...
Hi,
I have two nRF52833 and i want to make one tx and one rx (with an antenna array) for direction finding (AOA mode).
I have already compile the project called "direction_finding_connectionless_tx...
Hi I'm developing an application using SoC nRF52840 and I need to use load cells to measure some weights. A lot of existing solutions use the HX711 chip to amplify the differential...
Is there any peripheral sample for OOB legacy pairing? I'd like to know how to encrypt with temporary key( TK). I checked the ble_hids_keyboard_pair_nfc sample in the SDK...
Hello ,
I'm using the libuarte library so i can send data and receive it , i'm enabling RTC2,TIMER1,TIMER0 and TIMER2 .
this is the main definition of my libuarte NRF_LIBUARTE_ASYNC_DEFINE...
Hello,
As we are close to production of our new device, i would like to know what are the possible ways of performing OTA DFU in thread network from Thread Border Router...
