I'm trying to design a very low power sensor that takes readings using ADC and SPI 200 times a second. I'm a bit worried by the current EasyDMA uses (1.1mA). As far as I can...
Hi, I am working on a project where I want to make one nrf51288 chip as central hub and connect that to a android phone and other salve nrf51288 .
idea similar to this: ...
Hi,
I have a code programming the nRF51422 development board to write to a Sharp Memory 96x96 pixel LCD screen using SPI.
Currently the code writes two numbers and a...
I've modified the ble_app_uart example by adding GPIOTE so that the transmitter sends a character to the receiver when a GPIO pin is toggled. This part is working well.
...
Hi,
I am working on my hardware product having nRF-51422 chipset. I just came to know from forum post that
nRF-52 chips will get arduino IDE support as standalone. I want...
Hi!
I've been using PCA10028 for a long time and I had some bricking issues but I've managed to un-brick it with "nrfjprog --recover" and everything would work again. ...
I want to build nrftoolbox app in android studio. I downloaded the zip file from the github website and also the required dfu library. I unzipped both the files in a folder...
Hello,
I am using the Adafruit Feather nRF52 Bluefruit LE featuring Nordic's nRF52832 for a new project where I need to minimize power consumption as much as possible in...
I try to run Azure_IOT_Hub without HUB. I have set in prj.conf and prj_qemu_86.conf:
CONFIG_AZURE_IOT_HUB_DEVICE_ID= "mydeviceID"
CONFIG_AZURE_IOT_HUB_HOSTNAME="mydeviceIOTHub...
Hello,
NCS1.9.1,nRF5340DK,Windows10 X64,VSCode,
why frequent problems of "west flash --recover",
some time run cmd " west flash --recover",it will be ok,
and some...
Hi,
I'm trying to wrap my head around doing some basic GPIO reading, writing etc. and hopefully some interrupts. Apologies if these are basic questions - I've only really...
Hello dear People,
I would be very happy if anyone has an idea how to solve this.
The Problem is the following: I am using nordics lte link controller to connect to nb...
Hi,
1.) I am programming a custom board based on NRF52833 using NRF52833-DK using SWIO/SWCLK interfaces using Segger Embedded Studio with NCS v1.6.1. I am trying to print...
1. Your documents mention only SPI3 and SPI4 are available in non- secure mode.. which means spi-0,1,2 should not be available in non-secure mode.. But if i use nrfx drivers...
Hello.
It is under development using nrf52832 (S132 v7.0.1, SDK v17.0.0) as a peripheral device.
I'm currently considering Flash Data Storage (FDS).
As settings, "FDS_VIRTUAL_PAGES...
Hello.
Target nRF52832( nrf52dk_nrf52832)
SDK NCS v1.9.1
Build : SES for win 10 (5.68)
1. Support BT5.3
My project used nRF5_SDK_17.1.0_ddde560. Recently I found...
I am using a custom board design with a Nordic nRF52832 and have implemented the Nordic time sync algorithm outlined here ( https://github.com/nordic-auko/nRF5-ble-timesync...
Hi everyone,
I'm currently using nRF52832 with nRF5DK_V17.1.0 file.
I understand that this question has been risen up quite a lot however, I still do not understand why...
Hello Nordic team,
I am testing a timer using code snippet which Nordic team recommended as a reference. My code is something like this:
uint64_t start, stop;...
Hello,
A nrf52840 central device programmed with Soft-Device S132 and connectivity firmware, the host is interfaced via USB and uses PC-BLE driver API's to communicate with...
Hi,
I'm using nrf52840 DK and android based mobile with nrf connect for mobile app installed.
I would like to execute a freestanding sample code to transfer message between...
