Hi, is there an available developer in my tri-state area of Minnesota, N. Dakota, or S. Dakota? Please call me if you are available for a project for hire. The developer should...
I'm trying to design a very low power sensor that takes readings using ADC and SPI 200 times a second. I'm a bit worried by the current EasyDMA uses (1.1mA). As far as I can...
Hi, I am working on a project where I want to make one nrf51288 chip as central hub and connect that to a android phone and other salve nrf51288 .
idea similar to this: ...
Hi,
I have a code programming the nRF51422 development board to write to a Sharp Memory 96x96 pixel LCD screen using SPI.
Currently the code writes two numbers and a...
I've modified the ble_app_uart example by adding GPIOTE so that the transmitter sends a character to the receiver when a GPIO pin is toggled. This part is working well.
...
Hi,
I am working on my hardware product having nRF-51422 chipset. I just came to know from forum post that
nRF-52 chips will get arduino IDE support as standalone. I want...
Hi!
I've been using PCA10028 for a long time and I had some bricking issues but I've managed to un-brick it with "nrfjprog --recover" and everything would work again. ...
Hello everyone,
currently I'm working with NCS V1.9.1 and I was wondering if it is intentionally that the bt_conn_ctx_count() function always returns the CONFIG_BT_MAX_CONN...
Hi,
I have the exact problem in this issue: https://devzone.nordicsemi.com/f/nordic-q-a/60609/problem-with-mcuboot
NCS version: 1.9
Board: nrf52840dk_nrf52840
The...
Kind folks,
I have used the nRF Connect app on my MacBook Pro to (carefully!) install the new 1.9.1 SDK and the Nordic version of the SEGGER Embedded Studio. Using this...
Hi,
I'm running into a frustrating issue where I can get the NRFX_SPIM and my own BSP examples to work, but when I try to combine them - the buttons stop triggering their...
I have an existing system for my elderly mother based on a nRF52832 puck ( www.espruino.com/Puck.js ) that includes the button-press-count in its advertising data. When the...
Hello,
we want to communicate the BLE to BLE without connection how to communicate?
One BLE is continious on scaning mode and another one is advertising mode on event...
Tried to compile the Bluetooth: Peripheral UART-sample, (nRF Connect SDK v1.9.1) and got an error:
FATAL ERROR: command exited with status 1: 'c:\ncs\v1.9.1\toolchain\opt...
Hi,
I am devloping base on azure_fota example and got the Peer closed connection! after used the SAS URL.
First, I complete do the FOTA by using the normal URL from blob...
I am working on my nrf52810 . I just found an issue that, when my device enter DFU mode its show dfu trag , I can not return to the application(If I do not want to upload...
Hi,
1. Is bootloader file and firmware file, different for projects build on nCS..? Or a single executable build file consists both bootloader & firmware..?
2. Can you...
Hi
I am working on driver for SPIS and would like to run higher than 8 MHz. We have been doing some tests and seems like it is possible to go e.g. 10 MHz.
Is the nrf51810_PS...
Hi,
How can I put an application at a specific memory location?
I want to upload 2 programs to my device and switch between these applications. I modified the bootloader...
Olfox recently raised a concern with the 400kHz frequency setting for the TWIM peripheral, which I confirm is incorrect in the SDK (17) and nRF52832 datasheet (v1.7); I attempted...
As described in that PR I am getting a hard fault when trying to cancel a download.
https://github.com/nrfconnect/sdk-nrf/pull/6955
To reproduce this issue apply the...
