Hi, is there an available developer in my tri-state area of Minnesota, N. Dakota, or S. Dakota? Please call me if you are available for a project for hire. The developer should...
I'm trying to design a very low power sensor that takes readings using ADC and SPI 200 times a second. I'm a bit worried by the current EasyDMA uses (1.1mA). As far as I can...
Hi, I am working on a project where I want to make one nrf51288 chip as central hub and connect that to a android phone and other salve nrf51288 .
idea similar to this: ...
Hi,
I have a code programming the nRF51422 development board to write to a Sharp Memory 96x96 pixel LCD screen using SPI.
Currently the code writes two numbers and a...
I've modified the ble_app_uart example by adding GPIOTE so that the transmitter sends a character to the receiver when a GPIO pin is toggled. This part is working well.
...
Hi,
I am working on my hardware product having nRF-51422 chipset. I just came to know from forum post that
nRF-52 chips will get arduino IDE support as standalone. I want...
Hi!
I've been using PCA10028 for a long time and I had some bricking issues but I've managed to un-brick it with "nrfjprog --recover" and everything would work again. ...
Hello, there
We made a custom tracker device with nRF9160. During prolonged use, we observed that k_delayed_work_submit_to_queue sometime return -22 and cannot be recovered...
When i change the config NRF_DFU_BLE_BUTTONLESS_SUPPORTS_BONDS to 1
the following error comes, how do I overcome this?
<debug> app: nrf_dfu_svci_vector_table_set() ->...
Hello All,
I am facing binding error if I use UART1 for binding but UART0 is working fine. Refer the below error.
Please let me know the solution to solve this error....
Hey!
I'm trying to adapt a modified version of the open bootloader example for the nRF52820 MCU and have one issue as well as some questions.
I have adapted the build...
Hi,
I am developing a system consisting of a BLE peripheral and central with a custom service (SDK 17, S140, PCA10056).
For the peripheral, I am using a modified version...
I have noted that the code size of my project is reduced by more than a factor of two if I set NRF_LOG_ENABLED to 0. It is also reduced significantly if I set the Log Level...
Hi
I would like a clarification when performing DFU from external flash. This is applicable to both nRF52 and nRF91, I guess, as long as nRF Connect SDK and MCUboot is used...
I have provided the starting address and the size of the flash and ram in the linker script of the gccarm compiler, yet the sizes of the output hex file is different, could...
Hello My name is Yongmin Won and I work at EMC Labs in Korea. It's not different. You are about to operate the N52832 module as an Nrfgo program. But I want Bluetooth BLE2M...
Hello, We are building an OTA firmware update mechanism that relies on MCUBoot and the DFU Target API . We take the implementation of fota_download as an example.
Currently...
Hello Community, I know there are already a few posts on this topic, but I wanted to make sure this is conform with my application. I am trying to program an external board...
Hello!
I am a beginner trying to learn Zephyr using nRF52840 DK.
I tried to build the example present in the zephyr's samples/basic/servo_motor directory.
I made necessary...
Hello,
We intend to develop a new device. I found that nrf52 series can do non adaptative FHSS. Combined with a nRF21540 i would like to set the output to 20 dbm.
According...
I am working on BLE mesh project with Nordic thingy 91 and why trying to understand how to get it working. I previously program NRF52840 on my Nordic Thingy 91 via USB with...
