Hi, is there an available developer in my tri-state area of Minnesota, N. Dakota, or S. Dakota? Please call me if you are available for a project for hire. The developer should...
I'm trying to design a very low power sensor that takes readings using ADC and SPI 200 times a second. I'm a bit worried by the current EasyDMA uses (1.1mA). As far as I can...
Hi, I am working on a project where I want to make one nrf51288 chip as central hub and connect that to a android phone and other salve nrf51288 .
idea similar to this: ...
Hi,
I have a code programming the nRF51422 development board to write to a Sharp Memory 96x96 pixel LCD screen using SPI.
Currently the code writes two numbers and a...
I've modified the ble_app_uart example by adding GPIOTE so that the transmitter sends a character to the receiver when a GPIO pin is toggled. This part is working well.
...
Hi,
I am working on my hardware product having nRF-51422 chipset. I just came to know from forum post that
nRF-52 chips will get arduino IDE support as standalone. I want...
Hi!
I've been using PCA10028 for a long time and I had some bricking issues but I've managed to un-brick it with "nrfjprog --recover" and everything would work again. ...
Hello Nordic,
I was looking at multiprotocol support from nRF Connect SDK by following this link: https://developer.nordicsemi.com/nRF_Connect_SDK/doc/latest/nrf/ug_multiprotocol_support...
Hi
Trying to install and operate the Sniffer based on nRF52840 USB Dongle
Having the nRF Connect for Desktop installed and burned the Dongle in accordance with the instructions...
Sorry I have to see how the ssp of ublox work.(nina 410)
II have to send a packet over the serial every 50mS.The packet len is 100byte.
I see that some time the received...
Hey DZ,
I'm having some trouble with the download_client. It's not playing nice with the HTTP server I'm using. On the last chunk of data, the nRF91 is issuing a Content...
Hello everybody.
I am developing a firmware which allows us to send data bidirectional between Central and Peripheral. On the one side we have a nrf51-DK and on the other...
Hi
I'm working on an application that utilizes CODED_PHY.
I'm working on top of ble_app_blinky examples (central and peripheral).
I've seen this post on DevZone:
https...
Hi forum,
I am working on nrf52832, using sdk 15.0.0. I am working on Ble_beacon using sdk sample code.
In the Sdk_config.h file default enable uart0. Why this need to...
I am trying to get the nRF BLE Sniffer v3.1.0 working on my Mac running Bg Sur using a nRF52840 dongle. I have followed all the instructions listed in the sniffer document...
mergehex does work with file paths with "..\" in them. Here's my folder structure:
project root
Firmware
Application
Bootloader
SDK_Libraries
nRF5_SDK_17_0_2 ...
We are using nrfSDK1702. We have been trying to lower the current from a beacon. The beacon is active every 10s, then go back to sleep. The current consumption stays around...
Hi all! In my example after (i guess) 3 mins with out BLE connection the system goes to sleep mode. ¿Is there any way to avoid this ? Thank you so much!
Hi,
I'm connecting with my cell-phone for the field-try test.
I want to know the modulation type when it only use the connection type??
And what the modulation type...
Hey at all,
today I wanted to set up 7 new Thingy:91 devices. All thingys are 1.4.0 // 2020.23.
So I started with updating modem FW (mfwnrf9160123) and flashing thingy91_ltem_2021...
