Has anyone tried to generalize this example to different sized variables? What I would like to do is allocate a data structure, write that to flash, and recall it at a later...
I've a PCA10036 V1, I change the IC to nRF52822 QFAA-B016. With nRF5_SDK_11.0.0-2.alpha_bc3f6a0 and SD: s132_nrf52_2.0.0-7.alpha_softdevice, the programme started but if I...
Hi
We are developing software for the nRF51 with Keil under VirtualBox. Previously we used the PCA10000 dongle with the Master Emulator and MCP without issue. Now, with...
We are using nRF51822 for our products.
We want to know the min value of "Receiver sensitivity" when we use this chip for BLE.
The Datasheet says "Receiver sensitivity...
Dear
The BLE Multi-link example (ble_app_multilink_central and ble_app_multilink_peripheral)
shows how one central device can connect to multiple peripheral devices. ...
In the MCP app, if I have the following service data for an Eddystone beacon:
0x10, // Eddystone-URL type
0x00, // TX power in dBm. This is a signed integer so 0xEE ...
I have the nRF Control Panel Android application. It works fine with several BLE devices, but specifically for the Fitbit Flex, it fails to connect.
I know Fitbit wristbandes...
Hi everyone ! I am working at a project. I dont't know which mcu was used this project but it was written for pca10040 and used s132. Many values are write to flash memory...
I merged in some of my code to the examples/thread/dfu/client in the v4.1.0 SDK for Thread and Zigbee. After getting OTA DFU working, I moved onto some commissioning related...
Hi there,
i'm wondering if it's possible to get access from the demodulator directly within the nRF52? it shows in the block diagram below, is there any way to bypass...
Hello Nordic,
I'm trying to run nRF5_SDK_17.0.2_d674dde\examples\ble_peripheral\ble_app_uart (PCA10056, S140 softdevice) with default sdk_config.h . The master is nRF Connect...
Hi,
I am new to nRF Connect SDK. I am trying to achieve over the air Firmware upgrade through nRF5340. The SDK i am using is nRF Connect SDK v1.5.0 .
As per my understanding...
I am currently going through the usbd_ble_uart example and understanding what states make which LED's active,
Within the example, LED_BLE_NUS_CONN is defined as BSP_BOARD_LED_0...
How to use the internal 32.768k crystal oscillator for nrf5340？
NCS: V1.5.0
example: ncs1.5.0\v1.5.0\nrf\samples\peripheral\radio_test
Only HF no LF config.
Hi all,
I'm trying to use one of the built in sha256 libraries. As I've enabled the CONFIG_NRF_CC3XX_PLATFORM and CONFIG_NORDIC_SECURITY_BACKEND I thought I would pick this...
I am working on a BLE Product which connects to a remote device when detected within a certain proximity (based on the RSSI values). After switching on the scanning, I receive...
Hii Guys,
I am trying to run example code ble_app_uart on my nrf52810 sdk module . But when I try to run the code in debug mode I get an error of Vector Catch Error ....
Hi, I am working on nRF52840. I want to add GSM MQTT protocol. Is there nordic soc available for this? Which we can later communicate with nRF52840 peripheral device also...
Hi Everyone,
I am working on nrf52832, I am using sdk15.0.0 ble_beacon_app.
I want set tx_power but when softdevice enable gettting error.
I am tried using sd_ble_gap_tx_power_set...
Hi.
When I click add new LTE Device, I get the same menu as when clicking add new SIM Card. When is click register with IMEI and PIN assosiated to my nrf9160DK, I get. ...
Hello All,
I am developing a light control device using Zigbee and Alexa. I am using an nRF52840 device and SDK nRF5_SDK_for_Thread_and_Zigbee_v3.0.0_d310e71.
For my development...
Hello Everyone,
I am a beginner
I am working on a project which requires authentication of the firmware , for this purpose i want to generate the hash of the firmware...
