I'd like to erase all the pages managed by FDS as part of a "Hard Reset" operation. fds.c has a hint of a "FRESH_INSTALL" directive (part of an enum defined in fds_internal_defs...
nrf51822
SDK v10
SD S110 v8
hello!
My pj is about ANCS+nus+hid mouse sevices.
If my borad had bonded with an iPhone,then download new hex from mdk ,and run.
...
Hello.
I would like to develop FW for the nRF52832, using Eclipse IDE + ARM GCC + Segger JLink OB.
I've seen on the segger webpage that the nRF52832 is a Cortex M4 processor...
When using app_timer through scheduler, a break and go will overflow the event queue if a timer is a repeat timer. The effect is that it's not possible to debug.
To work...
I need to be able to actively set the value being incremented in the Timer2 register on the nrf52 (what I believe would be it's main register). It seems that this might be...
The errata for the nRF52 indicates higher consumption in managing timers and GPIOTE. Does the BSP for SDK11 follow recommended practice to deal with these errata can I ask...
Hi,
I am trying to understand the pstorage to record a log for temperature. In my code, I can call pstorage_init(), and clear a block but when I try to store some data...
Hello,
I have an nRF9160 DK and a Thingy:91. Both have been running asset_tracker for more than 3 hours, but none achieved an LTE Connection. I have installed the latest...
Hi, i am working with usb cdc driver (sdk 15.3 and nrf52840) and i have a problem . This is my variables initialization APP_USBD_CDC_ACM_GLOBAL_DEF(m_app_cdc_acm, cdc_acm_user_ev_handler...
Hello,
I send SMS from nRF9160 to my number using following method.
1. Open LTE Socket
2. Send AT Commands:
a. AT+ CFUN?
b. AT + CFUN = 1
c. AT+ CFUN?
d. AT...
Hi all, If using the RC LF instead of a 32.768KHz crystal are there any side effects of the 16ms calibration period which occurs every 4 seconds? I'm mostly concerned how...
Hi,
I am working on buttonless dfu example, but i want to design my application in such a way that, device should enter into dfu mode when button is pressed. I should be...
Hi, I have some issue about mesh network.
Using below developing environment.
- SEGGER Embedded studio for ARM V4.22
- nRF SDK 15.3.0
- nRF Mesh SDK 3.2.0
- chip...
Hello
I'm a beginner in Bluetooh and I bought two dev board NRF52840 DK. I would like to make a mesh with these two boards. One in master and the other in relay, the goal...
Hi,
I´m working with "TWI Sensor" example of SDK 16 and I modified the Main function of main.c as follows (just added NRF_LOG_INFO("\r\ntest") );:
I just added this...
Is there a good way to uniquely identify mesh node across multiple smart phones? The problem is: Android provides access to MAC addresses that can be used as identifiers of...
Hello. When I examined the BLE data format, I found that it was as shown in Figure 1.
Fig1
I am using NRF52832, please tell me how to detect the CRC value...
I am using mbedtls with ECB hard accelerator on nRF52840. So I changed the macro definition: UPDATE_CBC_MAC in ccm.c to function:
#define HT_UPDATE_CBC_MAC \
for ( i...
Hi All,
we're developing beacon that advertise both legacy and long range at the same time.
however we got NO_MEM error while adding 2nd adv set
any limit on multiple...
Hello,
I am working with the Interactive PyACI (nRF_SDK_for_Mesh 4.0.0 with boards nRF52832). I followed the tutorial "demo_configuration" present in the doc folder. Every...
Hi,
I am trying to test the radio example from Eclipse. So i took one of my projects on SDK15.2 that works with the NRF52832, I cloned it and renamed it.
The arborescence...
