I'm trying to design a very low power sensor that takes readings using ADC and SPI 200 times a second. I'm a bit worried by the current EasyDMA uses (1.1mA). As far as I can...
Hi, I am working on a project where I want to make one nrf51288 chip as central hub and connect that to a android phone and other salve nrf51288 .
idea similar to this: ...
Hi,
I have a code programming the nRF51422 development board to write to a Sharp Memory 96x96 pixel LCD screen using SPI.
Currently the code writes two numbers and a...
I've modified the ble_app_uart example by adding GPIOTE so that the transmitter sends a character to the receiver when a GPIO pin is toggled. This part is working well.
...
Hi,
I am working on my hardware product having nRF-51422 chipset. I just came to know from forum post that
nRF-52 chips will get arduino IDE support as standalone. I want...
Hi!
I've been using PCA10028 for a long time and I had some bricking issues but I've managed to un-brick it with "nrfjprog --recover" and everything would work again. ...
I want to build nrftoolbox app in android studio. I downloaded the zip file from the github website and also the required dfu library. I unzipped both the files in a folder...
Hi,
we are facing the following error. We bond our device (peripheral S140, SDK 15.3) with the following settings with iOS devices:
#define SEC_PARAM_BOND 1 // Perform...
Hi,
I am unable to build code. My Mac has just been updated to Catalina, not sure if that's caused the issue.
I am trying to build the standard "blinky" code but am getting...
Hello
I'm working on SDK v17. Receives certain data from the app, and LED timers work according to the data received.
The code that receives data from the app and parts...
Hello
I'm working on sdk v17. I want the LED to be printed out like a wave when I receive certain data from the app. (5 Times)
It is simple to use 'delay' and 'for' as...
I had my first encounter with Nordic chips a couple of years ago. To evaluate the devices, I used an nRF52832 to implement a small helper project. I was very impressed: it...
Hi Team, Is it possible to use the BLE NRF52832 module for audio applications like attending phone calls, listening music etc. If it is not possible with this module could...
I wrote this code to make a 1MHz signal clock with timer and GPIOTE.
It works fine without softdevice, but when I modify my app to use BLE, gpiote doesn't work (I...
Hai ,
I am using nrf52840 and 15.2 SDK for ota over BLE. I have made bootloader for OTA over BLE and tested same with nrf connect application using dfu package zip file...
I tried to make a copy of the Asset Tracker example application to start my own project. However I cannot get it to load in SES. I'm currently on the Master branch of nRF...
Hello,
Based on the DFU documentation, you should be able to download an updated soft device as long as the "major" number of the soft device does not change. This was true...
I recently designed a PCB and have been testing it.The PCB mainly consists of the Bluetooth Module BMD-350 ( based on NRF52832 SOC ) and HX711.( There is an accelerometer...
Hi. I have a question regaring the nRF52833. I want to program the MCU using ArduinoIDE and I'm not sure if I have to use a programmer to program the nRF52833 and if so do...
SDK 15.3
SD S340
Bootloader implemented to update over GSM and BLE. BLE update code is taken from example secure_bootloader_dfu*. GSM update code is custom made. SDK is...
I set up nrf52832 that it is called proxy device, i create a loop that proxy device will sent 20 message to app phone (Android) within 100ms. But my app (Android) receive...
