Hello.
I would like to develop FW for the nRF52832, using Eclipse IDE + ARM GCC + Segger JLink OB.
I've seen on the segger webpage that the nRF52832 is a Cortex M4 processor...
When using app_timer through scheduler, a break and go will overflow the event queue if a timer is a repeat timer. The effect is that it's not possible to debug.
To work...
I need to be able to actively set the value being incremented in the Timer2 register on the nrf52 (what I believe would be it's main register). It seems that this might be...
The errata for the nRF52 indicates higher consumption in managing timers and GPIOTE. Does the BSP for SDK11 follow recommended practice to deal with these errata can I ask...
Hi,
I am trying to understand the pstorage to record a log for temperature. In my code, I can call pstorage_init(), and clear a block but when I try to store some data...
I would like to source a compact BLE board to act as a lock controller developed with with a matching transceiver for use in a fob and an app.
It would toggle the pio and...
Ok so here is the issue. I was trying to build a simple application which is described in the tutorial for characters. After building an advertisement and understanding the...
I'm following pc-ble-driver compilation steps.
I could run "vcpkg install asio" and "vcpkg install catch2", but "vcpkg install --head spdlog" fails with error:
C:\dev...
Hello, I am usering nrf52840, now i am testing the current. i found that the current is 40uA in 0dBm while 201uA in 8dBm. maybe it is abnormal in 8dBm, what can i do to check...
Hi,
I am using NRF MESH SDK V3.0 ,nRF5_SDK_15.2.0 and with s132_nrf52_6.0.0_softdevice .
I've noted some problems when i try to use the app_timer in repeat mode with a...
Hi, I am fiddling with this example from the SDK: infocenter.nordicsemi.com/in...cp=5_1_4_3_1_2
In this example, there is a test regarding key derivation as:
As I understand...
I am getting intermittent pickup of advertising packet from a peripheral known to advertise every 2 second. Basically I get ~20 sec gaps where nothing is received.
Below...
I want to use the ble in nrf51822, and I use the example in nrf51_SDK_11.0.0 and softdevice in nrf51_SDK_11.0.0 \s130nrf51201\s130_nrf51_2.0.1_softdevice.hex(thougt the example...
Hello
I am currently looking for the best method to write and read values in the flash. My values are 17 uint16_t arrays with 216 indices per array. I would like to store...
Hello All I am new to this nordic semiconductors. I need information regarding nRF52840 DK boards.
* How to connect two nrF52840 DK(transmitter to receiver) and start advertising...
Hi, I have a SIM800L GSM/GPRS module that I can successfully talk to via the UART on the nRF51.
I can tell it to dial numbers etc and that all works fine.
My problem...
Hi, I'm using app_pwm with 32.768Khz external xtal. the following is my setting in sdk_config.h.
// <0=> RC // <1=> XTAL // <2=> Synth
#ifndef CLOCK_CONFIG_LF_SRC #define...
Hi,
I used sdk 15.2.0 version, I refer to the ATT_MTU Throughput Example to modify the Nordic UART Service (NUS) Application example.
Now I have some questions:
1. How...
Hello,
I'm using nRF52832, SDK15.0.0, Softdevice S132.
What should be the code added to application in order to support BLE DFU service?
I've been here , but its for...
hello,
I want to use RSSI on nrf52832, and the project is uploaded.
the question is, I test the RSSI on channel 2468MHZ， the NRF_RADIO->RSSISAMPLE result is about -92dBm...
Hi,
I followed the instructions for Getting Started with the NRF9160, activating the iBasis SIM card, placing into the board and applying USB power.
The first issue...
Hi,
I'm trying to update the firmware on my nRF9160 development kit
I downloaded the modem firmware and DFU tool
And then tried to follow these instructions: ...
