Hi, is there an available developer in my tri-state area of Minnesota, N. Dakota, or S. Dakota? Please call me if you are available for a project for hire. The developer should...
I'm trying to design a very low power sensor that takes readings using ADC and SPI 200 times a second. I'm a bit worried by the current EasyDMA uses (1.1mA). As far as I can...
Hi, I am working on a project where I want to make one nrf51288 chip as central hub and connect that to a android phone and other salve nrf51288 .
idea similar to this: ...
Hi,
I have a code programming the nRF51422 development board to write to a Sharp Memory 96x96 pixel LCD screen using SPI.
Currently the code writes two numbers and a...
I've modified the ble_app_uart example by adding GPIOTE so that the transmitter sends a character to the receiver when a GPIO pin is toggled. This part is working well.
...
Hi,
I am working on my hardware product having nRF-51422 chipset. I just came to know from forum post that
nRF-52 chips will get arduino IDE support as standalone. I want...
hello.
i am new to nrf52832
my question is when i press the button it will goes to interrupt handler then turn on the led if i press the same button led will turn off...
LTE link monitor does not work.
OS: Mac SEGGER IDE: v4.16 place: Tokyo in Japan.
I set up the environment from scratch following Get Started Assistant v0.9.2, updated...
Hi,
our installed base of sensors transmit their data in periodic BLE 4.0 beacons. I would like to develop a relay board that receives these beacons, and then retransmits...
Hi,
I want to use the nRF9160 DK for an NB-IoT application. I am located in Bavaria, Germany where there is no LTE-M coverage. I understand that I need the NB-IoT version...
To the kind attention of Nordic support team, from www.nordicsemi.com/ I downloaded all nRF24 Files.
I found very interesting the nRFgo Motherboard (nRF6310 Rev 1.4) pinout...
Hello ,
I am new to nrf52832
i am using external interrupt for led on and off
here the problem is when i press the button 1 led will turned on if i press the same button...
For Zigbee RF manufacture test, we did try nRF52840 using the sample code "radio_test" in SDK nRF5_SDK_15.3.0_59ac345,
but it seems that only the TX power information can...
Hi all,
I'm developing a buttonless DFU based application using the SDK v15.3 Following the documentation was pretty easy and I'm now able to run the app_ble_buttonless_dfu...
Hello All,
I am working on nRF51822. Use nRF51 SDk 12.3.0 version for reference. Writing program in IAR in windows.
Porting the OTA DFU to my custom APP.
use SDK 12...
Hello
I am developing a product by using nrf52840 and s340.
I know the way how to certificate ble. It is using the dtm example.
But I don't know how to certificate...
Hi
I have a question.
I am using USB CDC UART example code for my application development.
I have changed VID and PID in sdk_config.h file as per requirement.
Now...
Hi All,
I want to communicate ST25R3911B with nrf52832 controller,
It is interfaced on SPI controller.
I could not find any API related to this in SDK 15 but while searching...
Hi!
I'm having issues compiling the nRF9160 samples in the SDK. I've followed the Getting Started Assistant. I'm currently on the master branch. When I check out the v3...
I am able to see all the other three packets (URL, UID and TLM) in Eddystone Validator app except the EID packet. But I am getting the EID packet in 'nRF beacon for Eddystone...
Hi everyone,
We are going to certify a TRAXENS product design that contain an electronic card with a nRF52840 module on it. For that, we want to communicate with the nRF52...
