Suppose there are 10 BLE peripherals in a room and one BLE Central,then is there any way i can get the list of available peripherals[name or id.. etc]?
I am using NRF5182...
I am using SDK_11 s130 on nrf51-dk. When err_code is any value other than NRF_SUCCESS, APP_ERROR_CHECK(err_code) will cause nRF51-dk board to reset. How can one get APP_ERROR_CHECK...
Hello All,
I have problem with ble_app_uart which are not support DFU services.
When I am implement both services device will not advertise. and when ble_nus uninitialized...
[symptom]
I want to update my application/bootloader/softdevice by DFU.
Steps are shown below.
bootloder/softdevice update
if 1 step is done, application update...
Dear Developer Zone,
I am new to ANT and am looking for someone to help me to setup an example 15 channel (14 devices) ANT network using the S332 soft-device to test communication...
Hello,
i am working with the Enhanced ShockBurst proprietary protocol and i am wondering where I can find the sources of this protocol, so that I can do some changes. ...
[uart - Copy.rar](/a master _error.png ttachment/3cc01f5e2484d2b0f33e62befd3e6a62)
hello there
I am interfacing master nrf51 dk with nxp's slave lpc11u24
(1) my main...
Steps to reproduce:
1) Set up slave device
Device: nRF52832 SDK: v15.0.0 Soft Device: S132 v6.0 Examples: Any 6lowpan example (including ipv6_medium_ble)
Disable 6lowpan...
When adding two more characteristics to my custom service, I get error #4 which is an out of memory error. The log is working but it does not show the settings for what I...
Hello,
I'm working with SDK 15.0 and Softdevice S132 6.0. I have two nRF52832 boards (the BMD-300 Evaluation Kit and the SparkFun nRF52832 Breakout ).
I am running ble_app_hrs...
I am quite confused about how to go about programming the nRF52840 Dongle. The "programming" page on infocenter says that it can be programmed through the nRF Connect Programmer...
Hi everybody!
I would like to ask the following nRF52840 has the function of preventing current reverse irrigation?
Or what circuit prevents nRF52840 current from flowing...
Hi,
We're designing a BLE module, which is fairly straightforward. The design contains a nRF52832 + SKYWORKS SKY66403-11 FEM. We set the nRF52832 to transmit at -4 dBm and...
Hello,
I'm working on Keil with SDK 15.0 and Softdevice S132 6.0. I'm trying to run the Nordic UART Service example. I have two nRF52832 boards (the BMD-300 Evaluation Kit...
I have quite a few SPI peripherals to be interfaced with nrf52840 chip, for example, Ethernet plug, ATWINC1500 WIFI module etc. What example should i start with to get an...
Hello,
I am using NRF52840 and NRF52832 SoCs for different roles to be played in a BLE Mesh Network. As of now i am using NRF52840 DK and Holyiot-17095 for evaluation purpose...
Hi everyone,
I went into the bootloader mode with the nRF52840 DK accidentally so I immediately turned off the DK and powered it back on. However, after powering the DK...
Hello all,
We are using nRF24L01+ as Rx in an embedded system and we are experiencing the following problem:
The MCU that operates the radio can be manually reset (a...
My nRF52 DK has PCA10040 V1.1.0 2016.34 682272915 on a label.
It works fine when connected to my laptop over USB. If I try to power it from the coin battery underneath though...
Hello, we are using a radio module with the nRF51822 for our telemetry system.
In order to conduct the EMC test of EN 301 489-1, I would like to clarify the 6dB bandwidth...
