Suppose there are 10 BLE peripherals in a room and one BLE Central,then is there any way i can get the list of available peripherals[name or id.. etc]?
I am using NRF5182...
I am using SDK_11 s130 on nrf51-dk. When err_code is any value other than NRF_SUCCESS, APP_ERROR_CHECK(err_code) will cause nRF51-dk board to reset. How can one get APP_ERROR_CHECK...
Hello All,
I have problem with ble_app_uart which are not support DFU services.
When I am implement both services device will not advertise. and when ble_nus uninitialized...
[symptom]
I want to update my application/bootloader/softdevice by DFU.
Steps are shown below.
bootloder/softdevice update
if 1 step is done, application update...
Dear Developer Zone,
I am new to ANT and am looking for someone to help me to setup an example 15 channel (14 devices) ANT network using the S332 soft-device to test communication...
Hello,
i am working with the Enhanced ShockBurst proprietary protocol and i am wondering where I can find the sources of this protocol, so that I can do some changes. ...
[uart - Copy.rar](/a master _error.png ttachment/3cc01f5e2484d2b0f33e62befd3e6a62)
hello there
I am interfacing master nrf51 dk with nxp's slave lpc11u24
(1) my main...
Hello all, to optimize the BOM and size of our device(Tag based on nRF51822), the external divider was replaced by software configuration to measure the battery voltage. In...
Hello,
I have seen, that the BLE MAC is increased by one, in dfu_transport_update_start() (dfu_transport_ble.c).
Can someone give me a short explanation, why this is done...
I have successfully compiled BLE application using tutorials provided on nordic website.
but when I start doing debugging for better understanding find out that I can not...
I configured the bootloader to preserve one page of data ( I configured #define DFU_APP_DATA_RESERVED 0x400 on the bootloader project
I also made the same thing with my...
Hey,
We got a problem when trying to figure out how to detect the custom services from Unity. We are trying to read data and afterwards to do some manipulations of objects...
I am trying to implement the following sequence, using SD s130 :
GATTS Queued Writes: Stack handled, one or more attributes require authorization (var #1)
First thing...
I started with programming my nrf52 dev kit board with the soft device (v2.0.0-7) programmed using nRFgo, and then bootloader (from dfu_dual_bank_ble example) programmed using...
setup, I have a 3.3 V battery divided down to the bandgap range using a 56k and 10k resistors, so the voltage at the ADC input is 3.3 * (10/66) = 0.5 V，but the fact is 0.498V...
When I run try to generate code for a simple Blood Pressure profile I get a run time error. I'm using Plugin 1.2 with Studio 1.0.2095. Any ideas on how to fix it?
1:25...
I'm putting out this scenario I don't understand, yet, to see if anyone else might have experienced the same thing.
I have a demo with a central and peripheral that bond...
Best Regards,
while messing around with nRF51822 S130, timeslot API and nRF Master Control Panel, we noticed that:
Issue : if a packet is formatted correctly, but the...
Best Regards,
I am developing a firmware version for nrf51822 based on Softdevice S130 (old v8.1) and Timeslot API.
Currently, I can freely transmit and receive packets...
I'm using the NUS service for a sensor design. It was working fine for me. I don't know what is changed, but I experiences the next problem.
When I connect my sensor using...
What is the RF Connector on NRF52 Preview DK? It looks like U.FL/IPEX/MHF but it does not have the central pin. I want to find a converter to SMA. Could you please suggest...
Hello,
I am currently working on a hard metal project involving Nordic product with Bluetooth.
I have to implement Bluetooth Smart for a bare metal project and I've already...
