Hi all !
I'm trying to evaluate the throughput i can have between a Motorola 4G and the nrf51. The nRF51 is the peripheral and the phone is acting as a central.
To do...
I have a digital microphone chip, it has the CLK, DATA, LR_SEL three pins, now I will pick up the three pin nrf5283 three pin is as follows: CLK connectionI2S_CONFIG_SCK_PIN...
Hello, Nordic Team, I'm embedded designer from Russia, discovered your amazing wireless MCU NRF52832. I looked through your SDK and peripheral drivers, and unfortunately found...
Thanks Stefan. The zip file making and updating steps work perfectly for me, if I follow your steps and make it from your stock pre-built "dfu_test_app_hrm_s132.hex". My question...
Hi!
I'm trying to configure my NRF8001 module with the help of nRFgo studio. I'm using Nordic UART over BTLE service template. The module can be discovered via nRF Master...
I'm trying to make a BLE device that actually pairs securely. I posted this question on StackOverflow but didn't get any answers - maybe someone here knows more. As far as...
I work on a project where we make a device with a 9160, and our application is build using NCS 1.7.0 and is programmed with MFW 1.3.0. The network our devices connect to is...
I have basically all my code disabled, all I do in main() is get a pointer to the "zephyr_console", suspend it and return.
This gives me an average power consumption of...
Hello,
I try to dfu with mcumgr but I feel like the download speed is a little slow. So I want to increase download speed. I think that mcumgr has the command to set boudrate...
Hello,
We are designing a board with a nrf5340 with a VDD of 1.8V.
The board is very small and it's complex to fit all the components on it.
We are thinking of removing...
Hello,
I was wondering if there is away to perform DFU using SPI without smp protocol or mcumgr from one nRF52840 to another? What I am trying to do is to send a firmware...
Hi,
We are trying to attain power optimization in our project, which uses the nRF5340 board. In our code we have implimented RTOS, BLE for data transfer and are using i2c...
Hi,
I encountered an issue since i upgraded nrfjrpog
My previous version was 10.13.0
And now is 10.24.2.
I have a batch file to program my device and until the upgrade...
We need very fast Wi-Fi transfer rates at times. I have been able to tune the code and Wi-Fi driver settings to get up to 30-35 Mbps which is great. But if I don't throttle...
Hi,
Added a function to the coap_client sample code that executes otInstanceFactoryReset by pressing a button and sets it to factory shipping mode. However, it appears that...
I'm developing a system where I want to connect simultaneously to different BLE and ANT+ sensors. I'm using the nRF5340 DK and I would like to be able to select which sensors...
I have a project that I'm pulling in code from multiple_adv_sets using v2.7.0 and sysbuild.
talks about the opcodes and status being in the spec? https://www.bluetooth...
Hello,
We are designing a board with a npm1300 and a nRF5340. A button is connected to npm1300 SHPHLD.
On short-press, we want the npm1300 to send an interrupt to the...
Hi team,
We tested the nRF7002 with the nRF5340 as the host. Now, our application needs to connect the nRF7002 Wi-Fi module with a custom microcontroller other than Nordic...
Hello,
I am trying to establish communication between the nRF9160 SoC and the nRF52840 on the Thingy:91. I have two arrays: one of 774 bytes and another of 8 bytes. Currently...
