I have a digital microphone chip, it has the CLK, DATA, LR_SEL three pins, now I will pick up the three pin nrf5283 three pin is as follows: CLK connectionI2S_CONFIG_SCK_PIN...
Hello, Nordic Team, I'm embedded designer from Russia, discovered your amazing wireless MCU NRF52832. I looked through your SDK and peripheral drivers, and unfortunately found...
Thanks Stefan. The zip file making and updating steps work perfectly for me, if I follow your steps and make it from your stock pre-built "dfu_test_app_hrm_s132.hex". My question...
Hi!
I'm trying to configure my NRF8001 module with the help of nRFgo studio. I'm using Nordic UART over BTLE service template. The module can be discovered via nRF Master...
I'm trying to make a BLE device that actually pairs securely. I posted this question on StackOverflow but didn't get any answers - maybe someone here knows more. As far as...
I am using esb in SDK 11 and my understanding is that the radio causes interrupts that are forcing and cannot be disabled. These in turn causes software interrupt 10 to be...
Hi,
I'm trying to build the SLM application on the SIAA chip (w/o GPS). I'm modifying from the nrf9160df_nrf9160 board, but no success there. Is it possible to build the...
When I set the GPIOE pin to float, NRF_DRV_gPIote_IN_config_t config = GPIOTE_CONFIG_IN_SENSE_TOGGLE(true);
The power difference between true and false is 10uA, but when...
Hi All
I have been successfully using a jlink flasher for quite a few years now but after upgrading the segger drivers as i have always done ever couple of months i now...
Dear Nordic Developer Zone,
Is there a way to set the LFCLK (32.768kHz) on a GPIO using nRF52811 ?
I want to use this clock for controlling another device.
Best reg...
I'm trying to implement OTA DFU in our custom App with our nRF52832 acting as the device to be upgraded. Everything seems to work OK in that:
1. New image uploads to the...
I have configured a composite USB device on nRF5340 with DFU+CDC+Audio interfaces and enabled MCUBoot. Trying to perform DFU using dfu-util tool on Windows always fails. Following...
Dear Nordic Engineers
I have a problem and would like to ask you about the frequency offset of NRF5340.
As we all know, if I would like to adjust the frequency offset...
Hi everyone,
I am currently working with NRF52833 and SDK 17.0. Everythings went pretty well, however, now i need to have some memory check in runtime since i used a lot...
Hi guys
I ve made a custom board using the nrf52811 SoC,and now i want to program it for testing.
The thing is i am really lost on what to do, this is the first time...
I wanted to use SES (6.32b) to build an example app (nRF5_SDK_14.2.0_17b948a, ble_app_blinky) and run it on a Nordic dev board (nRF52840 Development Kit), but crashed.
...
Hi there,
I just followed all the steps (twice) and I still cant get the welcome screen to show up. I cant get anything to show up when i click on create a new (anything...
I'm attempting to create and then update some NFC data to be presented as a type 2 device.
When I call nfc_t2t_payload_set it returns -45 (EDEADLK) but since the library...
We are using the DFU workflow available with nRF5 SDK 16.0.0 and nRF5 SDK 17.1.0 on our BLE devices. We have two different products, one using the nRF52832 and the other using...
If a manufacturer ships a large number of nRF52840 based devices that are configured as Zigbee end devices, and then later decides to switch them to Zigbee routers through...
I am using the Sparkfun thing plus nrf9160 feather with SDK 2.0.0 and modem firmware 1.3.2. Ultimately I would like to get LTE working along with GNSS, however, I can't even...
