I have a digital microphone chip, it has the CLK, DATA, LR_SEL three pins, now I will pick up the three pin nrf5283 three pin is as follows: CLK connectionI2S_CONFIG_SCK_PIN...
Hello, Nordic Team, I'm embedded designer from Russia, discovered your amazing wireless MCU NRF52832. I looked through your SDK and peripheral drivers, and unfortunately found...
Thanks Stefan. The zip file making and updating steps work perfectly for me, if I follow your steps and make it from your stock pre-built "dfu_test_app_hrm_s132.hex". My question...
Hi!
I'm trying to configure my NRF8001 module with the help of nRFgo studio. I'm using Nordic UART over BTLE service template. The module can be discovered via nRF Master...
I'm trying to make a BLE device that actually pairs securely. I posted this question on StackOverflow but didn't get any answers - maybe someone here knows more. As far as...
I am using esb in SDK 11 and my understanding is that the radio causes interrupts that are forcing and cannot be disabled. These in turn causes software interrupt 10 to be...
Hello DevZone:
I can see that they are working on a module with WIFI6, my questions are the following.
Will the module have its own evaluation board or will it be integrated...
Very quick question:
I've created a device which implements the Legacy DFU Service. I've also created an Android Application that I plan to develop to be able to conduct...
My application code running on nrf51822 calls sd_ble_gatts_value_set to update a control characteristic. After 16 times receiving NRF_ERROR_BUSY status from this function...
Hi everyone,
first time posting here for me, let me know if i'm doing it wrong.
I'm currently developing a "modem module" built around nrf9160 and working with AWS using...
Hi,
With the NRF Connect SDK version 1.9.1 it is not possible to setup a Thread Coaps connection.
The DTLS handshake fails after Client Hello with an Alert message ...
Hi,
The below is our requirement for NRF5340
1. we have a DFU application with bootloader as an hex file
2. we have another app say blinky as an hex file
3. merge...
Hi all
My first post. I tried to finish one of Nordic tutorials. I need to use app from nrf connect(v 3.10.0): Bluettoth low energy (I have installed v3.0.1). I have nrf51DK...
got the thingy:91 following the getting started video had the bootloader updated and uploaded the right hex file for lte, the provided sim appears to be outdated so tried...
Hello, I am using the Asset TrackerV2 application (SDK 1.7.1) with the modem firmware (mfw_nrf9160_1.3.1). Recently the following error <err> aws_iot: getaddrinfo, error ...
Hello,
I have been developing on a nRF52832 DK using nRF5 SDK v17.1.0, and am very close to a production ready state. The final program will use soft devices, app_timers...
I want to develop a USB composite device using USB CDC ACM + USB Audio. I am not familiar with USB device protocol, so I hope to have a reference example. My development board...
I use the NCS version 1.9.0 with SES.I build and flsah successfully.I use the antenna array with 4x4,about 16 antennas.
In Tx,i use the Putty to debug serial.there is it;s...
Hi,
I have a hardware that I want to connect via BLE and send data via NUS (Nordic UART Service). I can connect to this hardware via the NRF Connect application on android...
Hello.
I get an error NRF_BREAKPOINT_COND. I use nRF5_SDK_17.0.2, s132_nrf52_7.2.0_softdevice and my kit - nRF52-DK.
An error occurs when trying to swap UART pins (Change...
Hello,
I want to establish 802.15.4 communication @ 1 Mbit between a nRF52840-DK and an ATmega256RFR2 based device. The communication works well with 250 kBit/s in RADIO_MODE_MODE_Ieee802154_250Kbit...
