Hi,
The situation:
I was able to successfully receive known packets from a device running gzp_device_dynamic_pairing, from, the host running the gzp_host_dynamic_pairing...
Hi everyone
nrf51822,softdevice s130 2.0.0
now i used softdevice s130 establish two connection as a central with two s110 peripheral device,at the same time i establish...
Hello , I want use nrf24lu as "Hos" and nrf51822 as 'Device'.
I need some info about nrf24xx whith gazell .but I can't find info bout those param like:
typedef enum...
When you download win driver (from www.nordicsemi.com/.../72324929 for instance). There's only a win32 dll/lib provided.
However, modern development are often made on 64bits...
hello, Nrf24LU (Rx) , nRF51822(Tx).
The Nrf24LU Can only receive one packet。
if I use this function twice ， like this：
The Nrf24LU can receive Continuous.
I guess The...
Hi,
I use SDK v10, S110 v8 and dfu_dual_bank_ble_s100_pca10028. My application has dfu support.
I reset to bootloader from application after writing 0x0104 to dfu control...
we have a 'long lived' tcp connection w/ regular data sends (1hz of 256 bytes for mqtt publishes) where sendmsg() sometimes returns EAGAIN. when trying again it usually works...
Hi Nordic team,
I am using the nRF52840 HCI USB project as the controller firmware, with a Linux device acting as the Bluetooth host.
My application has multiple BLE connections...
Hi,
I am developing on the nRF5340 and using an external modem and an external GNSS module. I am using SDK version 3.4.0.
To operate the modem, I use `modem_cellular...
Hello, We have some problem with connection to WIFI AP.
On NCS v3.4.0, once our device has associated with a WPA3-Personal AP, it can no longer
associate with a WPA2...
I am designing a board around the nRF52832 (QFN48). According to Table 5 in the product spec, GPIOs P0.22–P0.31 are marked "Low drive, low frequency I/O only" (see §4.3.1...
Hello,
Is modem fw `mfw_nrf9151-ntn_1.0.1` production-ready? Is it safe to have our manufacturer flash that instead of the `mfw_nrf91x1_2.0.4`. We are using the ncs-serial...
I'm trying to understand the npm1300-CAAA V1.1 example for configuration 1. The layout looks like this:
You can easily see that several pins are connected on the right...
According to the nRF52840 Product Specification, I observe only the typical value is specified below ：
ION_RAMON_RTC (System ON, full 256 kB RAM retention, wake on RTC...
Hi nordic
I am using the nRF54L10 and Nordic Zigbee Add-on version 1.3.0
I have probably been raising questions about polling for quite some time,
but I have not...
SUMMARY
A custom board (nRF52832, BLE Central + Peripheral roles simultaneously) reliably hits a hardware watchdog reset (RESETREAS shows WATCHDOG only, never CPU_LOCKUP...
Hello,
I have added DFU capabilities to my NRF54L15 project using:
CONFIG_NCS_SAMPLE_MCUMGR_BT_OTA_DFU =y
and
SB_CONFIG_PARTITION_MANAGER =y
SB_CONFIG_BOOTLOADER_MCUBOOT...
Hello DevZone Community,
I wanted to share a unique hardware-in-the-loop implementation using the Power Profiler Kit II (PPK2). While the industry is heavily focused on...
I am designing an FPGA to have a SPI slave port connected to the nRF5340 SPIM4 master running at 32 MHz. But the setup and hold times for this configuration are missing from...
I have an application which is not able to talk with my gas gauge device when the TI EV2400 can. Looking at the waveforms all look the same except for the Zephyr code has...
