Hi all !
I'm trying to evaluate the throughput i can have between a Motorola 4G and the nrf51. The nRF51 is the peripheral and the phone is acting as a central.
To do...
I have a digital microphone chip, it has the CLK, DATA, LR_SEL three pins, now I will pick up the three pin nrf5283 three pin is as follows: CLK connectionI2S_CONFIG_SCK_PIN...
Hello, Nordic Team, I'm embedded designer from Russia, discovered your amazing wireless MCU NRF52832. I looked through your SDK and peripheral drivers, and unfortunately found...
Thanks Stefan. The zip file making and updating steps work perfectly for me, if I follow your steps and make it from your stock pre-built "dfu_test_app_hrm_s132.hex". My question...
Hi!
I'm trying to configure my NRF8001 module with the help of nRFgo studio. I'm using Nordic UART over BTLE service template. The module can be discovered via nRF Master...
I'm trying to make a BLE device that actually pairs securely. I posted this question on StackOverflow but didn't get any answers - maybe someone here knows more. As far as...
Hello,
I need to connect a custom I2C device to the nRF52-DK, and I am using the sdk v1.6.0-rc2.
I am new to this development environment and I don't know how to initialize...
What is the max nb of periodic advertisers that can synchronize to a single receiver?
The bt_le_per_adv_sync struct defines a uint16_t sync handle so I infer that at least...
I am using the following example to load the code with Segger debugger and it works.
nRF5_SDK_17.0.2_d674dde\examples\ble_central\ble_app_blinky_c\pca10040\s132\ses
Now...
I noticed that when a BLE client disconnects and then reconnects to the, instead of receiving all data arriving over the UART from nRF9160 to nRF52840, there is a delay of...
Is it possible to perform two TWI Consecutive reads without sending the stop bit in between?
Example: Read 1 Byte - represent length (xxx) of data to come with second read...
I am trying to build a project with Visual Studio Code that uses MCUBoot. I have created a new project based off of the "Hello World" sample, which runs on my nrf52840 without...
Hello,
I have created different characteristics with the CCC macro (BT_GATT_CCC) that share the same "Configuration changed callback" function.
Inside the function below...
Hi,
I am using the download client library (MFW 1.1.4 due to Verizon compatibility) and am noticing that the TLS handshake with my server only succeeds after the first few...
Hi,
I am trying to build the bluetooth sample peripheral_lbs from the nrfconnect sdk. I get the following errors:
/home/newtrax/workspace/sdk-nrf/samples/bluetooth/peripheral_lbs...
How can i use the nRFConnect to read recognized gestures (idle, updown, rotate and tap) from the machine_learning application?
Tried to do this, but no services broadcast...
Hi,
When receiving BLE packets from another peer via different channels - in which stage does the peer understand if the packet belongs to him, or it's just a packet which...
Hello Nordic Team,
I need your help ! I have developed an App for nRF Connect for Desktop to be able to read and write UICR on device using nRF52 Series chips. It was working...
Dear Members,
I read about interrupt vector on S332_SDS_v2.0 page 78, 17.1.1 Interrupt forwarding to the application
=====
For the SoftDevice to locate the application...
Module NRF52832
Sdk: 15.2
I am trying to debug the module on a custom board, debugging worked fine until something weird happened on the specific board...
After the...
Hi,
I have nrf52840 DK connected to PC.
I have nRF5 SDK v17.0.2 installed.
I wanted to try out ble_app_blinky_pca100056_s140 example from the SDK, using Segger Embedded...
