Hello,
I have a device based on nRF51822 revision 2 and SoftDevice S110 v7.1.0. Because it is revision 2 it is affected by PAN44 and PAN45, and by default the SoftDevice...
Hi Guys,
I know this is more for software issues. But I was curious as to where I can find trusted case providers/makers for the nrf51822 Beacon. Can anyone from the community...
Hi,
Has anyone converted the Adafruit graphics library for Arduino, Adafruit_GFX.h, to be compatible with the nRF51?
Could you please advise on how to convert this Arduino...
Hi all,
I have a few questions:
How is that ADC's common mode rejection capabilities? Rejection for 60 Hz interference, etc...
The datasheet has "typical...
Hi all !
I'm trying to evaluate the throughput i can have between a Motorola 4G and the nrf51. The nRF51 is the peripheral and the phone is acting as a central.
To do...
I have a digital microphone chip, it has the CLK, DATA, LR_SEL three pins, now I will pick up the three pin nrf5283 three pin is as follows: CLK connectionI2S_CONFIG_SCK_PIN...
When using the local timer of the SAADC it should be started with TASK_START according to https://infocenter.nordicsemi.com/topic/ps_nrf52840/saadc.html?cp=4_0_0_5_22_4#concept_continuous...
Hi there,
I'm interested in using LittleVGL (lvgl.io) for my project. There is a LittleVGL example using nRF52840 in Zephyr project, but no in the nRF Connect SDK. Are...
I have successfully implemented the meander PCB antenna outlined in this app note, however, I am looking for and cannot find information on a shrunken version of this antenna...
I am trying to create an AOA link sending a CTE from an nrf52811 (BM833A module) and the receiver with an nrf52833 (bl653 module). Analyzing the CTE detection data, the first...
Hello guys,
I've a PCA10040 connected to my laptop.
It works fine with all the .hex BLE template example in the nordic SDK except with the UART example.
After download...
Hello,
I was using the usbd_ble_uart code for the nrf52840 dongle. When I connected the dongle to u-link 2 debugger and used keil uVision I was just doing my settings in...
NCS version：v1.5.1
board：nRF5340DK(0.11.0)
first，i use SES Embedded open radio_test project and choose nrf5340dk_nrf5340_cpunet ,and use [west flash --erase] download...
I am using nRF Connect SDK Tutorial - Part 1 | NCS v1.4.0.
I am using MacOS and nRF Connect SDK v1.6.1 .
a. The JlinkExe executes but JLinkRTTClientExe doesn't show any...
As noted in recent past cases, we have an issue with the state of the nRESET pin that is causing unwanted resets when connected/disconnected from external hardware (programmer...
I used NRF52840 Base on NRF SDK15.3 and freertos.
I have two task call nrf_crypto_aes_crypt a t the same time occasionally return NRF_ERROR_CRYPTO_BUSY. And also I add mutex...
Hi
I am developing with nrf52832 development board and sdk17. I'm trying to communicate with redpine rs9116w through spi but get some problems.
I have an other nrf52840...
Hi,
I'm a beginner at this, I'm a software developer so I've never worked with hardware but now I need to and I don't seem to be able to make it work.
I would need help...
Hi,
I have nRF9160 Power Measurement DK board, (PCA63511 Rev 1.1.0). And
nRF52 dev boards (nRF52840) (PCA10056)
I measured my program as: with nRFConnect version 3.2...
I have a project I have been working on for a touch switch using the nRF52840. I have been developing it using NRF Connect 1.6.0 and testing it on the nRF52840DK board. It...
