Hello,
I have a device based on nRF51822 revision 2 and SoftDevice S110 v7.1.0. Because it is revision 2 it is affected by PAN44 and PAN45, and by default the SoftDevice...
Hi Guys,
I know this is more for software issues. But I was curious as to where I can find trusted case providers/makers for the nrf51822 Beacon. Can anyone from the community...
Hi,
Has anyone converted the Adafruit graphics library for Arduino, Adafruit_GFX.h, to be compatible with the nRF51?
Could you please advise on how to convert this Arduino...
Hi all,
I have a few questions:
How is that ADC's common mode rejection capabilities? Rejection for 60 Hz interference, etc...
The datasheet has "typical...
Hi all !
I'm trying to evaluate the throughput i can have between a Motorola 4G and the nrf51. The nRF51 is the peripheral and the phone is acting as a central.
To do...
I have a digital microphone chip, it has the CLK, DATA, LR_SEL three pins, now I will pick up the three pin nrf5283 three pin is as follows: CLK connectionI2S_CONFIG_SCK_PIN...
Hi All,
I am new and trying to connect External BLE Pressure Sensor to NRF52840-DK Board
Do you have any example code for interfacing external BLE sensors that I can refer...
Hi, I am trying to connect the AWS_IOT library to a thread netork but find it really hard to get the TLS sockets working. I have connectivity for normal TCP and MQTT as well...
Hello,
our project has a requirement,
nrf52832 is used as a peripheral, and the mobile phone is connected to nrf52832.
The amount of data is relatively large. We want...
I want to use nvs in nrf cloud. A conflict is found between the nrf_cloud library and the nvs library. The nrf_cloud library will cause the nvs library to be unavailable,...
Hi, I have a product working with an android app with the nordic library for a nrf51822. I'm using auto connect but I would like just before performing a DFU to change this...
Hello,
I'm trying to run the MQTT simple sample, i don't know why but i can't build and run the project and also i cannot connect J-link.
Do you have any idea?
Thank...
Hi
If I log to RTT I can see ZCL packets decoded on the log using minimal logging but when i tried it with full logging (to get that on the zigbee_shell on the uart) I got...
Hello,
We have a custom design board using Raytac MDBT50Q-1MV2. We'd like to use the DC/DC regulator for REG0 stage for low power consumption. Please see the relevant part...
Hello,
In our product, we use the S132 v3 softdevice and legacy pairing with a static pin code. At startup, this pin code (that can be changed by the user) is read from...
in sample peripheral_uart in NCS1.5.0 ,I want to re-binding uart0 rx and tx pin . the default pin is p0.20 and p0.22 ,i want to rebind witn p1.0 and p1.1 .but i edit in prj...
Hello, I bought the Bluefruit LE Sniffer - Bluetooth Low Energy (BLE 4.0) - nRF51822 - V3.0 from Adafruit Bluefruit.
So, I downloaded nRF Sniffer for Bluetooth LE 3.0 and...
Hi,
I am trying to apply a whitelist during advertisement on my peripheral device. Only one central should be whitelisted at a time. The whitelist is empty on initial...
Hi,
I'm using nRF52840 with ble_app_uart of ble peripheral example. And I'm using IDE is SES.
I want to put two deep learning model into my project , the two deep learning...
Hello,
I have the NCS v1.5.0 and would like to use AES (in different modes) in my non-secure application.
Looking at the crypto libraries available described here http...
