Hello,
I have a device based on nRF51822 revision 2 and SoftDevice S110 v7.1.0. Because it is revision 2 it is affected by PAN44 and PAN45, and by default the SoftDevice...
Hi Guys,
I know this is more for software issues. But I was curious as to where I can find trusted case providers/makers for the nrf51822 Beacon. Can anyone from the community...
Hi,
Has anyone converted the Adafruit graphics library for Arduino, Adafruit_GFX.h, to be compatible with the nRF51?
Could you please advise on how to convert this Arduino...
Hi all,
I have a few questions:
How is that ADC's common mode rejection capabilities? Rejection for 60 Hz interference, etc...
The datasheet has "typical...
Hi all !
I'm trying to evaluate the throughput i can have between a Motorola 4G and the nrf51. The nRF51 is the peripheral and the phone is acting as a central.
To do...
I have a digital microphone chip, it has the CLK, DATA, LR_SEL three pins, now I will pick up the three pin nrf5283 three pin is as follows: CLK connectionI2S_CONFIG_SCK_PIN...
Dear Sir,
I'm use 2 nrf52840 chips to test sensitivity by nRF-DTM-1.0 tool.
I find out it's work on 1M and 2M but S8 and S2 can work.
The PER can't get 0% when I only...
Hi all,
I am developing BLE firmware to send and receive data between the development kit PCA10100 and nRFConnect App Desktop.
I'd like to notify the client (the App)...
Hi all, I am using SPIM with dma list triggered by gpiote. A gpio low-to-high event starts spim reading, and it works fine. However, I need to read different length at different...
Hi,
I am getting following problems while executing ble_gls example.
1.device gets disconnected immediately after connecting
2.getting timed out error problem
Kit...
Hello DevZone Developers,
Presently, I am trying to find H/W which support BT 5.1 Direction Finding.
I came across this , where it is mentioned that "Nordic Semiconductor...
Hello
I am contacting you because I have a problem with the "otThreadSendDiagnosticGet()" function. In my program, I am trying to retrieve the list of RLOC16s of the children...
Hi,
As I mentioned in the title, I am using the `pc-ble-driver-py` python package which is basically bindings to the SoftDevice running on the nRF52840 dongle.
Here...
hello Nordic
i am using nrf52840, sdk 16.0, working base on the peripheral app_ble_blinky example
i wish to use the p0_11 pin for pulse generation (not pwm), but when...
Hi,
We are running the smp_srv on the nrf5340 NET Core, we suspect the example is writing the firmware image to the NET core instead of the APP core. How do we have to modify...
Hello all! Where is located the i2c example for the nrf51822 device? I am using the nRF5_SDK_12.3.0 . And i can just find and i2s example. Best regards!
Hello. I'm currently developing a software for nRF52832AA device. It needs to communicate with external device via UART. It resieves text message and takes some data from...
Hi there,
My question refers to the nRF SDK: examples\dfu\open_bootloader\main.c
When the example is built, the output HEX file contains a section that writes the Bootloader...
How do I get putty to receive output from the Thingy91? I see output in the LTE Link Monitor with the following prj.conf config:
CONFIG_USE_SEGGER_RTT =y
CONFIG_RTT_CONSOLE...
Hi!
My apologies if this question has been asked and answered previously (searched, but didn't find).
We are still developing with ncs version 1.3.2, but would like to...
Hi,
can someone tell me the correct order of AT commands to connect to LTE, activate PSM?
My findings so far:
AT% XSYSTEMMODE=1,0,1,0 => set LTE-M and GPS mode...
