Hello,
I have a device based on nRF51822 revision 2 and SoftDevice S110 v7.1.0. Because it is revision 2 it is affected by PAN44 and PAN45, and by default the SoftDevice...
Hi Guys,
I know this is more for software issues. But I was curious as to where I can find trusted case providers/makers for the nrf51822 Beacon. Can anyone from the community...
Hi,
Has anyone converted the Adafruit graphics library for Arduino, Adafruit_GFX.h, to be compatible with the nRF51?
Could you please advise on how to convert this Arduino...
Hi all,
I have a few questions:
How is that ADC's common mode rejection capabilities? Rejection for 60 Hz interference, etc...
The datasheet has "typical...
Hi all !
I'm trying to evaluate the throughput i can have between a Motorola 4G and the nrf51. The nRF51 is the peripheral and the phone is acting as a central.
To do...
I have a digital microphone chip, it has the CLK, DATA, LR_SEL three pins, now I will pick up the three pin nrf5283 three pin is as follows: CLK connectionI2S_CONFIG_SCK_PIN...
Hi,
Since I updated nRF connect from 3.6.0 to 3.6.1, I get this error when I try to connect to a device :
"Error when getting device info: Error: Error: Error occured...
Hi,
I'm trying to devise the hardware platform for a Home Monitoring medical device. In the first place I planned to use the NORDIC nRF5340. With its large memory it would...
Hi.
We have a debug board for the NRF52832. The breadboard on this board is working fine. But if NRF52832 is used outside the debug board, then for some reason, some phones...
I want to set the Device's current date and time as I have to check time after certain interval. I don't want to use RTC where we have to look for ticks.
My questions...
Hello,
Could you please let me know if any of your devices would be suitable for our specific configuration?
We have a WMware server running many VMs. We would like to...
hello i am using nrf52832 and mpu6050 accelerometer with sdk 16 while programing i used 27 as scl and 26 as sda which is default in nrf52832 and i had no issues while reading...
Hi,
I am trying to test the light_lightness example present in ' nrf5_SDK_for_Mesh_v5.0.0_src' , on nRF52 Development kit(pca10040). And i am provisioning the device using...
I have a production device which I have soldered an SWD connection from a Keil project via the nrf51822 DK (port 20). I can flash code to this production device, but I cannot...
I'm using a SPI with a circular buffer so i need to have an interrupt with low latency that reset the RXD.PTR when the buffer is full.
The SPI is used for communicating...
Since Zephyr’s official BLE sample code, his BLE central only supports one central to one peripheral So I refer to the BLE central multulink officially provided by nordic...
HI ,
My name is MOHAMED ALI SAIDANE from Tunisia , i've been working on my project of the last year eduction , i'm interresting about the concept of the module NRF24l01...
We are using a custom ARM board which runs Linux and has a UART interface to a nRF9160.
I'm not how to phrase this exactly so I will just describe what I would like to do...
Hi,
I am using nrf51 DK and MDK is keil5
SDK : nRF5_SDK_12.3.0_d7731ad
softdevice : S130.
when i load the code nRF5_SDK_12.3.0_d7731ad\examples\peripheral\twi_sensor...
I have used light_Switch example from nrf mesh sdk nrf5_SDK_for_Mesh_v4.2.0_src I like to get the client source address in nrf_switch_server what should I need to modify to...
