Hi Guys,
I know this is more for software issues. But I was curious as to where I can find trusted case providers/makers for the nrf51822 Beacon. Can anyone from the community...
Hi,
Has anyone converted the Adafruit graphics library for Arduino, Adafruit_GFX.h, to be compatible with the nRF51?
Could you please advise on how to convert this Arduino...
Hi all,
I have a few questions:
How is that ADC's common mode rejection capabilities? Rejection for 60 Hz interference, etc...
The datasheet has "typical...
Hi all !
I'm trying to evaluate the throughput i can have between a Motorola 4G and the nrf51. The nRF51 is the peripheral and the phone is acting as a central.
To do...
I have a digital microphone chip, it has the CLK, DATA, LR_SEL three pins, now I will pick up the three pin nrf5283 three pin is as follows: CLK connectionI2S_CONFIG_SCK_PIN...
Target is nrf52832+SoftDeviceS132
When run ActiveScan,
Is SCAN_RSP advertise_report notified only after ADV_SCAN_IND advertise_report?
If I receive only the SCAN_RSP...
I used nrf9160 DK with sim LTE in Vietnam to run mqtt_sample. LTE link successful but I received the ERROR: getaddrinfo fail 51 and mqtt_connect 41. Please help me to solve...
I have some Nordic BLE peripherals. I'd like to develop a Python script to run on a Raspberry Pi to act as a BLE Central to connect to a couple of these peripherals. I've...
I have downloaded and installed nRF Connect v3.6.0.
I'd like to program a custom nRF5340 board, which I have connected to the nRF52833 dev-kit. When I go into Segger IDE...
Hi everyone,
I put below the link of a previous discussion. I refer to the main.c present in the discussion. I have a question about it.
In the main.c in the discussion...
I'm trying to evaluate the nrf5340 and flash a basic blinky application but I get an nrfjprog error when I run `west flash`:
[0/1] cd /Users/user/zephyrproje...Cellar...
I want to move the uart communication port from default pins to
#define RX_PIN_NUMBER 33 #define TX_PIN_NUMBER 34 #define CTS_PIN_NUMBER 35 #define RTS_PIN_NUMBER 36
I...
Hi There,
How to control led using pwm during dfu mode (when dfu programming is on going).
HW:PCA10056
SW: nRF5_SDK_15.2.0_9412b96
Example: ble_app_buttonless_dfu
I really did not want to ask, howeverI have spent a lot of time on this and still no joy.
I have a epaper shield have got the electronic paper display working. so SPI writes...
Hello,
I see on you webpage that there is an evaluation kit for nrf21540 -> PCA10112 . do you have the schematic of this board ?
For the moment I'm using the NRF52840...
Hi Guys,
We have a need to send data every 4 hours.
In order to do this, we sleep 1 hour at a time (1-hour timer - single shot) and increment counter, and when the count...
I'm using 2 nRF5340PDK with nRF Connect SDK 1.4.0. 1 PDK with central_uart and 1 PDK with peripheral_uart.
When I change the clock config of the peripheral_uart by using...
using nrf-9160dk and iBasis SIM with pre-built asset tracker app (2020-10-30_5522ca2b) and nrfCloud
First time the device was registered data transmission worked.
Now...
The design has 2 sensors on SPI with mode 3 and the nrf21540 which is mode 0. Can you have 2 different Modes on the same spi bus?
would i use the SPI transaction manager...
Hi,
I have the barest of PCBs with literally just the nRF9160, SIM slot and antenna, and have wired it directly to an Otii Arc, so there is no power circuitry either as...
