Hi, is there an available developer in my tri-state area of Minnesota, N. Dakota, or S. Dakota? Please call me if you are available for a project for hire. The developer should...
I'm trying to design a very low power sensor that takes readings using ADC and SPI 200 times a second. I'm a bit worried by the current EasyDMA uses (1.1mA). As far as I can...
Hi, I am working on a project where I want to make one nrf51288 chip as central hub and connect that to a android phone and other salve nrf51288 .
idea similar to this: ...
Hi,
I have a code programming the nRF51422 development board to write to a Sharp Memory 96x96 pixel LCD screen using SPI.
Currently the code writes two numbers and a...
I've modified the ble_app_uart example by adding GPIOTE so that the transmitter sends a character to the receiver when a GPIO pin is toggled. This part is working well.
...
Hi,
I am working on my hardware product having nRF-51422 chipset. I just came to know from forum post that
nRF-52 chips will get arduino IDE support as standalone. I want...
Hi!
I've been using PCA10028 for a long time and I had some bricking issues but I've managed to un-brick it with "nrfjprog --recover" and everything would work again. ...
Hi team,
I have to create a program which sends messages from one dongle to another. Now I have ported radio transmit and receive + USB CDC ACM programs for two 52840 dongles...
Hello,
I have experienced some softdevice hardfault in my multiprotocol application. I use https://github.com/NordicSemiconductor/nRF-IEEE-802.15.4-radio-driver/wiki with...
Hello,
My application, running on nRF52840 with SDK15.2, needs to detect the reset source from System OFF state. However, when using the BLE Secure DFU Bootloader, it always...
Hello,
I use nRF5SDK160098a08e2 SDK version, on ubuntu 16.04.
I use pca10056 (nrf52840 dev-kit).
I want to run cc310 example located at ./examples/crypto/nrf_cc310...
hello,
We have a product in production using nRF51422 and we are scaling up volume in a new manufacturing facility.
The functional tester stations require use of Master...
Hi!
Is there an example of how to use BLE_GAP_CONN_SEC_SET_MODE_LESC_WITH_MITM?
I cannot find one and I am having a hard time understanding what I need to do to make...
Hi,
I'm trying to use the pc-ble-driver "nrf-ble-driver-4.1.1-win_x86_32" to communicate with our nRF52-based embedded product. The fact that the PC and embedded implementations...
Hi,
I am using NRF52832 with secure bootloader to OTA my application in the field using Dual Bank updates and everything is working fine. In my application, I am using FDS...
Hi,
I need to use external eeprom memory AT24C256. I have not found any example for nrf52, so I started with migration existing arduino code to Nordic´s. Here is the Arduino...
Hey,
I am working on NRF51822, S130 softdevice integrating security, I have used the GLS as a reference for security implementation.
I have a use case in which I am...
I have both ble_app_uart_c and ble_app_uart they are automatically connected to each other if they are on. my question is ble_app_uart_c supports one to many or not? if it...
I am developing using pc-ble-driver-js and nrf52840 dongle.
We know that nrf's development tools (nrf connect ...) are being developed using an electron framework,
and...
We are using SDK 15.2.0 and softdevice s132 v6.10. we want to use the concurrent feature for broadcaster and observer. we wanted to just confirm that this feature is reliable...
Hi, I don't understand enough about electrical, but i found that a little piece of component in my nRF52840 dongle was gone.
It was something in this position:
It was...
Hello,
I'm trying to measure execution time of a piece of code in nRF52832. I was searching and found that I need to get the start time and finish time by using
beginval...
