Hello,
I have a device based on nRF51822 revision 2 and SoftDevice S110 v7.1.0. Because it is revision 2 it is affected by PAN44 and PAN45, and by default the SoftDevice...
Hi Guys,
I know this is more for software issues. But I was curious as to where I can find trusted case providers/makers for the nrf51822 Beacon. Can anyone from the community...
Hi,
Has anyone converted the Adafruit graphics library for Arduino, Adafruit_GFX.h, to be compatible with the nRF51?
Could you please advise on how to convert this Arduino...
Hi all,
I have a few questions:
How is that ADC's common mode rejection capabilities? Rejection for 60 Hz interference, etc...
The datasheet has "typical...
Hi all !
I'm trying to evaluate the throughput i can have between a Motorola 4G and the nrf51. The nRF51 is the peripheral and the phone is acting as a central.
To do...
I have a digital microphone chip, it has the CLK, DATA, LR_SEL three pins, now I will pick up the three pin nrf5283 three pin is as follows: CLK connectionI2S_CONFIG_SCK_PIN...
Hi,
I'm trying to implement a SPI Communication between Arduino UNO and PCA10056 DK. PCA10056 DK run as a SPI slave.. Arduino uno run as a SPI Master.
The problem is...
I'm using SDK 15.3.0 and SoftDevice 6.1.1 running on an nRF52832.
The iOS application works correctly when it is running in the foreground. It is able to connect and bond...
Hi,
I am trying to develop an application for Thingy:91, which would allow me getting data from BLE and sending it to the cloud with LTE. I am working on NCS 1.3.0.
Of...
I just tested with the example project, "ble_app_uart" using SDK, "nRF5SDK17009d13099.zip" on nRF52DK (labelled with PCA10040 1.2.4 2018.23) board on Segger embedded studio...
Hi ,
i am trying to interface a WINBOND W25Q64JV flash module with NRF52,i can able to read device id,status register success fully.
i wrote the data in particular address...
Hi,
I'm using nRF52840 DK as a central. Our project is based on ble_app_uart_c example. There is filter for UUID only during scan.
I noticed, that for conection establishing...
I'm using the nrfjprog command "nrfjprog -f nrf52 --reset". This sometimes causes my custom board to hang. I dont think it is able to boot at all, I do not see any uart output...
I would like to ask Nordic to create an example of an Android background service that can detect a device advertising.
Android imposes background execution limits which...
I am using nRF52840, SDK 16 + s140 with segger embedded studio.
I have already added NUS service to my application by taking reference to ble_app_uart example. I want to...
I need to somehow connect 10 i2c devices to nrf52, to do that I need 5 i2c peripherals, but nrf52 has only 2.
I see different options:
1) Use multiplexer. Probably a good...
Hello, support team.
I try to use nRF Connect v3.4.2 on Ubuntu 16.04.6, VMware.
But there is no response after executing specific application eg. Bluetooth low energy...
Hello everyone,
I have problem with a code for reading BME680. Here is my code the values display are wrong and never change.
Thank you for your time. I used this Library...
When adding the DK to my nRF cloud account, I get the following error message: " There was an error adding your device: nRFCode 40102: Ownership code [HWID] is invalid for...
nRF52840, SDK v16.0.0 SD140v7.0.1
Our electrical engineers gave us a hard ATT_MTU limit of 65 bytes, so as to keep the peak current low on the battery for our ultra-low...
