Hi!
I'm trying to configure my NRF8001 module with the help of nRFgo studio. I'm using Nordic UART over BTLE service template. The module can be discovered via nRF Master...
I'm trying to make a BLE device that actually pairs securely. I posted this question on StackOverflow but didn't get any answers - maybe someone here knows more. As far as...
I am using esb in SDK 11 and my understanding is that the radio causes interrupts that are forcing and cannot be disabled. These in turn causes software interrupt 10 to be...
I'd like to read and write data to the reserved app data space while in the bootloader. Is this possible with pstorage?
Because the BOOTLOADER_SETTINGS_ADDRESSS = 0x0003FC00...
Hi,
I am using 'pstorage_update' to store data in the internal flash. Whenever the number of bytes that should be written matches the size of a storage block everything...
Has anyone tried to generalize this example to different sized variables? What I would like to do is allocate a data structure, write that to flash, and recall it at a later...
I've a PCA10036 V1, I change the IC to nRF52822 QFAA-B016. With nRF5_SDK_11.0.0-2.alpha_bc3f6a0 and SD: s132_nrf52_2.0.0-7.alpha_softdevice, the programme started but if I...
Due to some problems with VTG and GND detect I sometimes program an on devkit nRF52 instead of my external board and that causes lost time, because it's not straightforward...
Apologies if this is answered in some other thread but we cannot find the precise answers we are looking for and are striving for some quick clarifications. We are planning...
The ble-sniffer_win_1.2_user_guide, Figure 4. Wireshark Interface, Packet Bytes window shows a 00 byte at location 0010, which corresponds to the "preamble" of the "Air Interface...
Hi
I want to declare 2 spi instances with only cs pin different.
The reason for dividing the two is because the modes are different.
The one declared above is executed...
I have used nRF5 SDK ver.16 for BLE HID digtiger.
I want to set up some feature value to HID report . Such as Contact count maximum.
I have followed keyboard example,...
I turned off the serial i n prj.conf of the mqtt_simple routine.
<prj.conf>
<nrf9160dk_nrf9160ns.overlay>
The idle current was measured at 500UA. This means that...
Hello Engineers,
We are trying to set the correct configuration between nrf9160 and nrf52840 for using the uart_pipe library. However we are still unable to communicate...
We have a Nordic development under way and I have run into a snag.
Neither of my dk board types (9160 or 52840) are recognized by jlink , no jlink drive etc….
I have personally...
So the interrupt on the nRF2401+ seems to be working inconsistently. I get interrupts sometimes and sometimes I don't.
For a context: I'm transmitting a sensor data only...
Hi, we recently purchased a Nordic Thingy 52 module and were trying to program it. We used a J-link recorder and a cable for the connection between the J-link and the Thingy...
Hi all,
I am using the nRF51822 and attach you can find the . .
I have noted that the current consumption is too hight for my scope (about 1.7mA). My idea is to 'reduce...
I tried: - changing USB cables and ports (no any improvement)
- instructions from this link devzone.nordicsemi.com/.../nrf52-dk-does-not-show-as-a-removeable-drive-in-windows...
Hi there,
My question is similar to https://devzone.nordicsemi.com/f/nordic-q-a/39447/central-role-in-a-mesh-proxy-node , but perhaps slightly different in that my existing...
DFU Trigger Library (USB) is indicated that only for nRF52840 SoC. For other SoCs, can I use it after some modification of the library easily? What's the limits?
Hi !
I am on a firmware project for a nrf52832. I am using SES on Windows.
There seem to be a problem when combining buttonless DFU and NUS. When I do the services_init...
