Hi Guys,
I know this is more for software issues. But I was curious as to where I can find trusted case providers/makers for the nrf51822 Beacon. Can anyone from the community...
Hi,
Has anyone converted the Adafruit graphics library for Arduino, Adafruit_GFX.h, to be compatible with the nRF51?
Could you please advise on how to convert this Arduino...
Hi all,
I have a few questions:
How is that ADC's common mode rejection capabilities? Rejection for 60 Hz interference, etc...
The datasheet has "typical...
Hi all !
I'm trying to evaluate the throughput i can have between a Motorola 4G and the nrf51. The nRF51 is the peripheral and the phone is acting as a central.
To do...
I have a digital microphone chip, it has the CLK, DATA, LR_SEL three pins, now I will pick up the three pin nrf5283 three pin is as follows: CLK connectionI2S_CONFIG_SCK_PIN...
Hello, Nordic Team, I'm embedded designer from Russia, discovered your amazing wireless MCU NRF52832. I looked through your SDK and peripheral drivers, and unfortunately found...
Hi there! I am developing a device with the nRF52810 that requires the following:
Receive audio over BLE
Store audio in memory
Playback audio on command
Would...
SDK 15.2 API 6.10 SES custom board
I am trying to get DFU to work and it is not seeming to work right.
I am trying to engage DFU mode by holding in button on board for...
Dear DevZonee's
Im trying to esablish a BLE connection using the following configuration of the peer-manager:
* LESC
* Just Works -> IO-Caps none (0x03)
If i run...
Hello
I am using SDK12.3 on nRF51822 chip using Keil V5 on windows 10.
I am using experimental_ble_app_buttonless_dfu example and bootloader_secure example.
They both...
Hello!
SDK 15.3
If I build secure_bootloader example project using Segger Embedded Studio it works, I can see it nRF connect.
If I build it using armgcc it does not...
Is there any actual difference between "Fast Advertising", and "Slow Advertising" - or is it just a way to easily specify two different sets of timing parameters?
The question...
Hi,
I'm having problems with the bootloader in SDK 15.2. I'm using an NRF52840, I don't know if the CryptoCell is giving me issues.
The DFU fails when checking the FW...
Hi All,
Sorry if this is a simple question, but I can't seem to find an example where the device is programmed as both RX and TX. (The examples have either one or the other...
Hello,
I am developing application which allows multiple central devices (phones) connect to a single peripheral device (custom board with nRF52840). I took example from...
We are under development on our custom board. then we suddenly were able to flashing the firmware, hex files onto our target board. SES showed the popup message such as "...
Hello,
I am unable to flash target board using my nrf52840 Dev board. I have two dev boards and I am able to flash the target with the other dev board.
The target board...
To what values should I set the PWMCON register to so that the PWM0 and PWM1 frequency is output at 20Khz with duty cycle varying between 1 to 2ms. Now specifically I am asking...
I am new to Bootloader and was going through the Secure BL example without SD but with UART
Here I observe that the Linker Option Shows the RAM and ROM address for the Bootloader...
hi....to everyone
Here i am using latest version 3.1 mesh , i have made some changes in light switch example , in order to get a character instead of bool value . i am getting...
Hi everyone,
I want to change the Y-axis on the AVERAGE plot to show real-time data from 0 uA to 10 uA. The default setting is -100.000uA to 15.000 mA.
The PPK manual...
