Hi, I am working on a project where I want to make one nrf51288 chip as central hub and connect that to a android phone and other salve nrf51288 .
idea similar to this: ...
Hi,
I have a code programming the nRF51422 development board to write to a Sharp Memory 96x96 pixel LCD screen using SPI.
Currently the code writes two numbers and a...
I've modified the ble_app_uart example by adding GPIOTE so that the transmitter sends a character to the receiver when a GPIO pin is toggled. This part is working well.
...
Hi,
I am working on my hardware product having nRF-51422 chipset. I just came to know from forum post that
nRF-52 chips will get arduino IDE support as standalone. I want...
Hi!
I've been using PCA10028 for a long time and I had some bricking issues but I've managed to un-brick it with "nrfjprog --recover" and everything would work again. ...
I want to build nrftoolbox app in android studio. I downloaded the zip file from the github website and also the required dfu library. I unzipped both the files in a folder...
Hello,
I have a device based on nRF51822 revision 2 and SoftDevice S110 v7.1.0. Because it is revision 2 it is affected by PAN44 and PAN45, and by default the SoftDevice...
Hi, I have tried to run nfc example, but it doesn't working, accidentaly i have found out that if supply 3V nfc not working, but if supply 2.7V and less it works, what is...
Hi, I'm designing based on the Altium files, but I'm not an antenna expert so I would like to know if you have any antenna recommendation for a low profile, because the one...
Hi,
I'm working on nrf52832 NUS. When i connect to device with "nrf connect app" i can see the data coming from sensor. But few seconds later device disconnect.
When...
Hello
I have 3 nodes, 2 Thread CoAP servers and 1 BLE/Thread Coap client.
Let's call them THnode1, THnode2 and BLE_THnode0.
I do not know the IP addresses of any node...
Hi,
I use "printf" or "app_uart_put" function to print message to UART., how can I check "all of the data had been transmit out complete"?
Thank you,
Chianglin
Hi, I want to test sending multiple packets of data with each packet having the maximum possible size of 247 bytes. I am currently testing with nRF Connect app. When i try...
I use nRF5_SDK_for_Thread_and_Zigbee_2.0.0_29775ac.
Example nRF5_SDK_for_Thread_and_Zigbee_2.0.0_29775ac\examples\thread\cli\uart\pca10056.
define BOARD_PCA10059.
...
I am using nrf51822. Separately BLE and flash are working perfectly alright. But when I comment err_code = ble_advertising_start(BLE_ADV_MODE_FAST); this line flash is working...
Hello,
As per my understanding, SPP was supported by BT Classic and no more supported in BLE. I have a device, which runs SPP. It has to be connected to the BLE client....
Hi, I am now developing a product which uses nrf51422 chip. In this product, I use buttons to turn on and off (since I don't have hard-power cut off circuit, we use system...
Hi
I wonder if the SDK DTM example can be used with a Rhode & Schwarz CMW500 unit. Are the commands compatible with each other, i.e. expected by the CMW500 and DTM example...
Hi,
we're evaluating NRF52 as a platform for a project in the agricultural space and I have some beginner's questions:
Is it feasible to use a timer firing at 100kHz...
Hello,
I created a custom board with the BMD350 module (it has a nRF52832 chip), and I a trying to program it with the BMD300 eval board.
The module on my custom board...
I am using a nRF51422 device with the SDK 11. The task is to transmit battery service data to an application on the phone. I was wondering if there is a tutorial available...
Hi,
I used "ble_image_transfer" sample code and can get the all the stuff I want and now I'm implementing the central device for it,
but somehow I always got the "cccd_configure...
