I'm trying to design a very low power sensor that takes readings using ADC and SPI 200 times a second. I'm a bit worried by the current EasyDMA uses (1.1mA). As far as I can...
Hi, I am working on a project where I want to make one nrf51288 chip as central hub and connect that to a android phone and other salve nrf51288 .
idea similar to this: ...
Hi,
I have a code programming the nRF51422 development board to write to a Sharp Memory 96x96 pixel LCD screen using SPI.
Currently the code writes two numbers and a...
I've modified the ble_app_uart example by adding GPIOTE so that the transmitter sends a character to the receiver when a GPIO pin is toggled. This part is working well.
...
Hi,
I am working on my hardware product having nRF-51422 chipset. I just came to know from forum post that
nRF-52 chips will get arduino IDE support as standalone. I want...
Hi!
I've been using PCA10028 for a long time and I had some bricking issues but I've managed to un-brick it with "nrfjprog --recover" and everything would work again. ...
I want to build nrftoolbox app in android studio. I downloaded the zip file from the github website and also the required dfu library. I unzipped both the files in a folder...
Hello,
I want to set the nrf24le1 module into register retention mode with timers ON but clock source from XOSC32K. I need this power saving code in my project. Also can...
Hi,
I am using adafruit Bluefruit BLE SNIFFER. My question is whether it is required to use jLink along with it to connect to it via USB. Also, I have a question can I sniff...
sdk5 15.2's app_timer.h at line 61 says:
* @details Use the USE_SCHEDULER parameter of the APP_TIMER_INIT() macro to select if the * @ref app_scheduler should be used or...
I am trying to read hts221 and ccs811 sensors from thingy and want to make the data available on UART(P0.02,P0.03).
I have tested the uart code and able to print data -...
Hi all,
I am trying to configure the LPCOMP module of the nrf52832 using registers directly, that is, without using the already generic functions that come with the sde...
Hello
I have two similar (as their producer says) boards. Both nRF52832. The main difference is in modems used for external data transmission.
SDK 15.0.0
SD 132
I...
I have an application using mesh SDK 2.1.1 that is working. I am migrating to V2.2.0. In my current code I use nrf_mesh_opt_set() to enable and disable a relay feature. I...
Hi,
Can nRF Sniffer v2.x software flashed in nRF52832 used along with wireshark sniff all BT 4.0,4.1,4.2,5.0 packets?
Please confirm so that we can proceed to buy the...
Hi there,
The DFU Nordic samples have a 4K "MBR Params" page, located in the last 4K of flash. e.g., the linker file has:
MBR_PARAMS_PAGE (rw) : ORIGIN = 0x0007E000...
Hi,
I need to minimize the power consumption.
For this reason when my device is in advertising the peripherals:
TWI
hight frequency clock
external interrupt on...
SDK version 15
I'm adding two more BLE services to my working custom one. And ran into some advertising issues. This is what's spitted out from GDB.
ble_advertising_init...
I'm working on the the provided example ble_app_uart , and I want to make the LED blink while the data is being sent from the peripheral to a smartphone application by BLE...
Hi,
Having worked with your software on and off for some time now there are a few things I have noticed that are slightly disturbing when it comes to the SDK.
Usually...
I am doing a register retention gzll transmit code with ADC. But problem is that the ADC value transmitted is always 255, if I connect ground to ADC it would read 247. Why...
Hello,
I am using nRF52480, s140 , SDK_15.0 and using a rscs central example. I used
uint32_t current_time = app_timer_cnt_get(); NRF_LOG_INFO("current_Tick: %02d", current_time...
