Hi all !
I'm trying to evaluate the throughput i can have between a Motorola 4G and the nrf51. The nRF51 is the peripheral and the phone is acting as a central.
To do...
I have a digital microphone chip, it has the CLK, DATA, LR_SEL three pins, now I will pick up the three pin nrf5283 three pin is as follows: CLK connectionI2S_CONFIG_SCK_PIN...
Hello, Nordic Team, I'm embedded designer from Russia, discovered your amazing wireless MCU NRF52832. I looked through your SDK and peripheral drivers, and unfortunately found...
Thanks Stefan. The zip file making and updating steps work perfectly for me, if I follow your steps and make it from your stock pre-built "dfu_test_app_hrm_s132.hex". My question...
Hi!
I'm trying to configure my NRF8001 module with the help of nRFgo studio. I'm using Nordic UART over BTLE service template. The module can be discovered via nRF Master...
I'm trying to make a BLE device that actually pairs securely. I posted this question on StackOverflow but didn't get any answers - maybe someone here knows more. As far as...
The GPS antenna just fell off the board. Seems like the part has a cold solder joint. This led me thinking that the LTE antenna might also have the same problem. I had no...
I choose one NRF52 DK(nrf52840_pca10056) for my daily development. After hundreds of erase and write cycles, the DK won't behaves like it should do. The other DKs runs well...
Hi,
In the registery definition of nRF52840 it is stated for PSEL.TXD:
Reg ID: A -> from bit 0 til 4 for Pin selection
Reg ID: B -> bit 5 for Port number
In this case...
I am looking into interfacing a SD card to the nRF52840. I have used the FatFS example and that is working ok with SPI. Then I have looked at the QSPI example and that also...
Hello,
I am using sdk 12.2 and nrf52 dk.
I am storing some data in flash using ( sd_flash_write((uint32_t*)0x4F800,m_deadbeef, sizeof(m_deadbeef));) and I am able...
Hi
I got the problem to connect customer board(nRF52) via SWD.
My connection should be fine and customer board is also supplied 3,3V by external power.
How I wire 52Dk...
Hi,
I want to add fstorage functionality to my applikation. I added all the files and functions as in the fstorage example from Nordic, but I get a linker error that the...
I am using an RTC to periodically kick off a PWM pulse train. This all works beautifully, but draws far more current than expected. From what I've read, this is because the...
Hi,
I've been working to get a Ublox GPS module to interface with my NRF52840 DK over UART. The GPS device boots up and starts streaming data almost immediately.
I am...
I am nRF52832 , S132 , SDK15.0.0 // nRF52840, SDK15.0.0 is used.
Examples of esb_prx, esb_ptx are modified and used.
Transmitter : nRF52832
Receive : nRF52840_DK
Senders...
hello
I have once again issues when I want to write a 'long" characteristic e.g. 85 bytes.
1) if I use a smaller MTU e.g. 23 or 50, I received corrtectly the User Memory...
I would like to design a BLE-controlled electronic device. My requirements are:
1- Very low power consumption. (Less than 200uA in IDLE mode)
2- Slow periodic BLE advertising...
We are a module manufacturer and have used the 52810 as a serial port transparent transmission module.
1. Our customer reports that when we put "More service uuid" into...
Hello there,
We're developing a chip with a nRF52840 as the only processor, which we're trying to get certified against 802.15.4. However, we had problems passing the radiated...
