Hi!
I'm trying to configure my NRF8001 module with the help of nRFgo studio. I'm using Nordic UART over BTLE service template. The module can be discovered via nRF Master...
I'm trying to make a BLE device that actually pairs securely. I posted this question on StackOverflow but didn't get any answers - maybe someone here knows more. As far as...
I am using esb in SDK 11 and my understanding is that the radio causes interrupts that are forcing and cannot be disabled. These in turn causes software interrupt 10 to be...
I'd like to read and write data to the reserved app data space while in the bootloader. Is this possible with pstorage?
Because the BOOTLOADER_SETTINGS_ADDRESSS = 0x0003FC00...
Hi,
I am using 'pstorage_update' to store data in the internal flash. Whenever the number of bytes that should be written matches the size of a storage block everything...
Has anyone tried to generalize this example to different sized variables? What I would like to do is allocate a data structure, write that to flash, and recall it at a later...
I've a PCA10036 V1, I change the IC to nRF52822 QFAA-B016. With nRF5_SDK_11.0.0-2.alpha_bc3f6a0 and SD: s132_nrf52_2.0.0-7.alpha_softdevice, the programme started but if I...
we found a device using onsemi rsl10, it can keep ble broadcasting with current below 30uA, and can be connected by mobilephones
we tried to get a similar effect using...
hardware: power profile kit rev 1.1, nrf52840DK
mode: power profiling with DK
I am power profiling my application and found that if there is no current in the system,...
In NRF Mesh Android, when we set the init value for sequence number (SequenceNumber.java), it will check the sequence value stored in SharedPreferences and return 0 if SharedPreferences...
Hi,
as a new year's gift I've noticed s332 v6 is available from ThisIsAnt's download page. I'm developing on nrf52 using SDK v14.2 since it was the latest supported for...
Hi,
I am testing the light switch sample in mesh sdk 2.2, in server part I need to drive an I2C slave device, which may take some time to init, so I put the init code after...
Using SDK 15.
adc_read works properly in main loop.
When called from an APP_Timer or from BLE connect event, function hangs. I set a breakpoint at the handler, and breaks...
The documentation states, “Only one data pipe can receive a packet at a time”
So what is the minimum acceptable delay between the receipt of two packets to two different...
Hi,
I have gone through PPK user guide but it is not working out.
In my setup I am using
One DK as external SEGGER JLink
One PPK as standalone power profiler
One...
Hi,
I want to interface wifi module(for example ESP8266 ) with nrf52832.
I need to transfer some data (received through bluetooth) to cloud(AWS).
Can I expect esp8266...
I have been trying to get the Timeslot API working with v15.0.0 of the nRF5 SDK, and have not had any success. All of the examples that I can find are built for much older...
I'm trying to implement the HID service on a custom nrf52832 board, unfortunately I'm running into problems.
Here's what happens: Advertising, connecting to the board,...
Hi,
I think I already know the answer but just to be sure, there is no difference on using printf (with added retarget library) and the app_uart_put() since printf will...
Hi, This is what constant carrier looks like at 2450MHz on my custom board using DCDC disabled
This is with DCDC enabled:
It can also look much worse with no real...
Hi there,
I'm looking at porting (i.e. re-implementing) an Arduino project to the nRF52832 to take advantage of the s212 or S332 softdevices. This chip is a few orders of...
