Hi all,
I have a few questions:
How is that ADC's common mode rejection capabilities? Rejection for 60 Hz interference, etc...
The datasheet has "typical...
Hi all !
I'm trying to evaluate the throughput i can have between a Motorola 4G and the nrf51. The nRF51 is the peripheral and the phone is acting as a central.
To do...
I have a digital microphone chip, it has the CLK, DATA, LR_SEL three pins, now I will pick up the three pin nrf5283 three pin is as follows: CLK connectionI2S_CONFIG_SCK_PIN...
Hello, Nordic Team, I'm embedded designer from Russia, discovered your amazing wireless MCU NRF52832. I looked through your SDK and peripheral drivers, and unfortunately found...
Thanks Stefan. The zip file making and updating steps work perfectly for me, if I follow your steps and make it from your stock pre-built "dfu_test_app_hrm_s132.hex". My question...
Hi!
I'm trying to configure my NRF8001 module with the help of nRFgo studio. I'm using Nordic UART over BTLE service template. The module can be discovered via nRF Master...
Hello,
I am facing issue while initialising seed by calling "mbedtls_ctr_drbg_seed" function I am getting -0x34 error and when I analysis this I got to know that I have...
Hello,
It has been a while since I have done any controlled impedance and was wondering if someone could provide me a quick sanity check before I continue:
Here is the...
Hi,
Does nRF52840 support stable modulation Characteristics
It is found that Stable Modulation Characteristics fail during the test, and the capacitor of the debugger...
Hello everyone,
I'm using nRF52832 with SDK v17 (S132 Softdevice).
I don't know why, but I can't disable softdevice. I can enable it normally, but when i make use of...
Hi,
I’m looking to monitor LTE-M or NB-IoT packets sent by the Thingy:91 in real-time using an app or software. Currently, I’m using the Thingy:91 to send temperature logs...
Dear devzone,
I followed this instruction to use nRF54L15-PDK v0.8.1 to burn external boards. The wiring diagram is as follows:
Command line input: nrfutil device recover...
I have a Minew MSR01-B milimeter wave sensor and I would like to know if there is any nordic hardware that i could use to comunicate with MSR01-B sensor, get the data and...
Hello,
I am designing a battery monitoring circuit for a 3.0V CR2032 coin cell using the nRF52840, and had some questions. I am following the battery monitoring circuit...
Good afternoon,
I have successfully established a 2.4GHz Zigbee network using nrf52540 + Zephyr + ZBOSS. Now I need to switch to sub-1GHz band - suits better my application...
Hello,
I am trying to implement BLE DFU with nRF7002DK and SDK 2.7.0(Sorry but not use sysbuild yet.)
https://academy.nordicsemi.com/courses/nrf-connect-sdk-intermediate...
Hi! I'm trying to find examples for a use case we might be exploring. Specifically, we'd like to connect an nrf52833/20/other to an Ipad over a USB HID interface. The connection...
I am trying to work through the Dev Academy - nRF Connect SDK Intermediate - Lesson 3 Exercise 1. I have run into a problem in step 8. Everything prior has gone OK and I successfully...
New nRF5340 DK board - PCA10095 2.0.2 2024.32 1050055047
HP Laptop with Window 11
Installed nRF Connect for Desktop v5.1.0
DK board is detected
Attempt to program...
I'm trying to make a template project tidier while waiting for an answer to a question and have removed a load of functions from main to serial.c but VSC is telling me
it...
