I've a PCA10036 V1, I change the IC to nRF52822 QFAA-B016. With nRF5_SDK_11.0.0-2.alpha_bc3f6a0 and SD: s132_nrf52_2.0.0-7.alpha_softdevice, the programme started but if I...
Hi
We are developing software for the nRF51 with Keil under VirtualBox. Previously we used the PCA10000 dongle with the Master Emulator and MCP without issue. Now, with...
We are using nRF51822 for our products.
We want to know the min value of "Receiver sensitivity" when we use this chip for BLE.
The Datasheet says "Receiver sensitivity...
Dear
The BLE Multi-link example (ble_app_multilink_central and ble_app_multilink_peripheral)
shows how one central device can connect to multiple peripheral devices. ...
In the MCP app, if I have the following service data for an Eddystone beacon:
0x10, // Eddystone-URL type
0x00, // TX power in dBm. This is a signed integer so 0xEE ...
I have the nRF Control Panel Android application. It works fine with several BLE devices, but specifically for the Fitbit Flex, it fails to connect.
I know Fitbit wristbandes...
Hi,
The situation:
I was able to successfully receive known packets from a device running gzp_device_dynamic_pairing, from, the host running the gzp_host_dynamic_pairing...
Issue: No Interrupt Signal on GPIO0 Pin of MAX30208 Sensor with Xiao BLE nRF52840 Using Zephyr NCS v2.6.1
I was write a code for max302078 sensor driver but in this i want...
In some examples that use nrfx libraries it is necessary to extract a GPIO PSEL, which is usually done like this. Give the following DT definitions
``` leds {
compatible...
Hello. I am developing a product equipped with BLE communication function using nRF52480. I am experiencing an issue where the BLE connection cannot be completed.
[Environment...
Looking at the uart_nrfx_uarte2.c driver it appears that Nordic is not looking for the compatibility string in the driver but instead is looking for uart0,uart1, etc. This...
Dear Support-Team,
due to the 2KB limitation of the secure buffers of the nrf9160 modem I am trying to setup native tls. I found the https_client sample which sounded promising...
Hi,
I am using nrf52840 with SDK 16.0. We wanted to dynamically allocate 49kb and 75kb of memory. Is there is any risk while de-allocating? Is it recommended to use the...
Hello,
I have a product that uses just works pairing, as the user should walk up to the device to pair (but not bond). As this is using Just Works, the connection should...
Hello, I have an Adafruit nRF52840 Feather Express , and I'd like to be able to flash the micro through the USB virtual COM port because it has to go in a case and the SEGGER...
We have devices in the field with one MCUBoot Key and we'd like to get all of our devices on the same MCUBoot Key to make managing the fleet easier.
Is it possible to migrate...
The PTX is nRF24L01+ and the PRX is nRF52833.
The code for the nRF24L01+:
Everytime I call NRF24L01_TxPacket to send out 32 bytes data I get the error code MAX_TX ....
TOOL : NRF SDK 2.6.99 (VSC)
1.When connecting a broadcast audio source with USB audio to listen to music on the sync side, there seems to be some stuttering. How can I solve...
I have been working on snoring detection using thingy53 project which is there in https://www.electromaker.io/project/view/snoring-detection-using-nordic-thingy53-backup#...
Hello,
I am trying to flash the Serial LTE modem on the nrf9160 on a custom board using the nrf5340DK and the nrf Connect Programmer. I am using the P20 port on the DK and...
HI
I am planning to test it by linking the DTM of nRF Connect For Desktop.
However, I am contacting you because the DTM does not work.
The nRF52-DK board operates...
