I'm trying to make a BLE device that actually pairs securely. I posted this question on StackOverflow but didn't get any answers - maybe someone here knows more. As far as...
I am using esb in SDK 11 and my understanding is that the radio causes interrupts that are forcing and cannot be disabled. These in turn causes software interrupt 10 to be...
I'd like to read and write data to the reserved app data space while in the bootloader. Is this possible with pstorage?
Because the BOOTLOADER_SETTINGS_ADDRESSS = 0x0003FC00...
Hi,
I am using 'pstorage_update' to store data in the internal flash. Whenever the number of bytes that should be written matches the size of a storage block everything...
Has anyone tried to generalize this example to different sized variables? What I would like to do is allocate a data structure, write that to flash, and recall it at a later...
I've a PCA10036 V1, I change the IC to nRF52822 QFAA-B016. With nRF5_SDK_11.0.0-2.alpha_bc3f6a0 and SD: s132_nrf52_2.0.0-7.alpha_softdevice, the programme started but if I...
Hi
We are developing software for the nRF51 with Keil under VirtualBox. Previously we used the PCA10000 dongle with the Master Emulator and MCP without issue. Now, with...
Could you please clarify for the clock and oscillator setup, are the LFXO oscillator and LFRC RC oscillator internal oscillators on the chip? Or is an external oscillator...
In the devzone there is a list of the "Recent and unreplied" posts, but is there a way to just browse all the devzone posts? Not just the "Recent and unreplied" list.
I...
I am debugging an issue where my nRF9160 (NCS 2.7.0) rolls back to the previous firmware after a seemingly successful upgrade. I am not getting enough logs from MCUboot to...
I was in the process of evaluating a driver when I noticed I2C communication was not working as expected. I put a probe on the relevant pins and noticed the Voltage on my...
Dear Nordic Specialist,
I would like to ask about the correct usage of the power recommendation parameter in the channel sounding configuration.
In bt_le_cs_set_procedure_parameters_param...
Hi，
Recently, I encountered a problem.
I wanted to set a MAC address of type BLE_GAP_ADDR_TYPE_RANDOM_PRIVATE_NON_RESOLVABLE, with the upper two bits set to 11 as well...
Hi,
I am using nRF9151 with nRF Connect SDK 2.9.0 .
In our project we are using an external NAND flash (MT29F4G01ABAFDWB) over SPI, and it is working successfully. We...
Planning on using the npm2100 PMIC as our PMIC for an upcoming asset tracking solution. We will have an accelerometer that will determine when the main MCU (nrf54) wakes up...
Hello,
I would like to know if it is possible in a Mtter project, to activate or not the MRP messages as mentionned in Matter Core specifications ( chapter 4.12. Message...
NCS 3.02 + nRF54L15
I'm troubleshooting a potential bug. Are these blocking routines, or if not how do I monitor for successful completion of flash write? I looked the the...
I found a issue, I open a sample project " v2.5.0\nrf\sample\cellular\location"
when I click "Add build configuration", no nrf9160 option and only nrf52840 can be selected...
Hi, I am trying to do pwm a rgb led using nrf54l15dk and custom board using nrf54l15 on port1 with pin connections on (p1.10, p1.8 and p1.13 for custom) or on (p1.11, p1.12...
Greetings,
I have worked with the MCUBoot and its Serial Recovery feature with success and recently tried to enable the CONFIG_BOOT_SERIAL_WAIT_FOR_DFU option ( as well...
Hello,
I am intending to extract audio from the onboard microphone of nrf5340-audio-dk.
I used the nrf5340_audio application as reference but cutting off the bluetooth...
Hi,
I'm trying to use same UART channel on both project-specific purpose and MCUmgr DFU. However, when I enable the option CONFIG_MCUMGR_TRANSPORT_UART, the code reset's...
