Hi,
I use HID application with S110 v8.0 profil.
I use BLE HID Keyboard example.
I put datas from smartphone to BOOT KEYBOARD OUTPUT REPORT and I whant read them by...
Hi all,
I use nRF51822 module and my environment is Eclipse + GCC + SDK 10.0. I refer to the example in path <SDK_PATH>/examples/ble_peripheral/ble_app_template, then make...
I am using nrf sniffer for trouble shooting. But it always exit unexpectedly. Wireshark was still open but the DOS window got closed.
I am attaching the log.txt.
log...
Hi all,
I am using ble open mesh with pca10028 boards ble mesh is working fine.
I am developing a application that has to blink led in mesh( without any delay between...
I'm still on stack 8.0.0 so it might have been fixed since. I have noticed that if the other side de-asserts CTS the Nordic code will leave the TX asserted in a Break condition...
Hello,
I'd like to ask what is the data rate when using BLE OpenMesh network and how much it depends on network architecture.
I'm considering using it in a network consisting...
Hello Nordic Community,
I need to know how to import my PCB design from Eagle to CST Studio to simulate it and I need to know if the simulation step will be useful to enhance...
Hi,
I am currently using the NRF52840 DK to evaluate the NFC functionalities of the SoC. It works very well with a smartphone.
I'd like to understand the NFC on the NRF52840...
Hi,
We are developing a matter curtain product the power by battery.I setup SED mode for low power. The larger the POLL PERIOD value I set , the worse the real-time performance...
Dear Support team
I don't quite understand the part as the picture below after I read the specification, I would like to kown What are the output drive modes in the picture...
I want to make an NFC card with Ntag 213, which is an NFC Type 2 tag.The card needs to write data to a specific block via NFC.
However, the NFC Type 2 tag library does not...
Hi, as stated at page 15 in the Direction Finding white paper(nWP-036), it says 'When the last switch pattern is reached and IQ sampling continues, the switch pattern loops...
//nRF52840 DK//PCA10056//central=apple-smartphone//Wireshark Version 4.0.1 (v4.0.1-0-ge9f3970b1527) sniffer.//
Wireshark is working perfectly on Advertising packets, but...
Our project was previously functional when we were developing using the nrf52840dk_nrf52840 with an overlay to reconfigure for our custom pcba. We created a custom board config...
Hi,
Is the nRF9160 capable of operating on the CBRS band (b48)?
I know it is not listed as a band that is supported by HW but I am curious if there is a software workaround...
Hi Nordic Team,
I am working on the BIS demo, I have three nRF5340 DK audio boards, so I set one as Source, two others as Sink, so is there any resources that when Source...
Hi,
After lots of issues with build and deploy, I eventually have a working version of a BLE App running on a XM122 Radar module. This module have to be packeaged with the...
Hi devzone
there are 2 nrf52 dk board - one is client(ble_app_blinky_c) and the other it peripheral(ble_app_blinky)
and I made it so that if you push the button3 on...
I need to port some functionality that is using nRF5 SDK 17.0.2/ S332 SoftDevice v6.1.1 to an older firmware using nRF5 SDK v12.0.0/Softdevice 332 v2.0.0. It looks like Softdevice...
I'm trying to build the documentation on a Windows 10 system. I've installed all of the required tools and made it to step 4 when I get the following:
C:\ncs\v1.9.1\nrf...
Hello All,
I have a problem when I build my project from sample central_uart & peripheral_uart .
I have two nrf5340 called A and B . B scans the broadcast to A to establish...
I'm having problems reading channel AIN7 in the rRF52, SDK11
I configure every channel in a similar way:
//adc_channel_5
{
nrf_saadc_channel_config_t channel_config...
