I'd like to read and write data to the reserved app data space while in the bootloader. Is this possible with pstorage?
Because the BOOTLOADER_SETTINGS_ADDRESSS = 0x0003FC00...
Hi,
I am using 'pstorage_update' to store data in the internal flash. Whenever the number of bytes that should be written matches the size of a storage block everything...
Has anyone tried to generalize this example to different sized variables? What I would like to do is allocate a data structure, write that to flash, and recall it at a later...
I've a PCA10036 V1, I change the IC to nRF52822 QFAA-B016. With nRF5_SDK_11.0.0-2.alpha_bc3f6a0 and SD: s132_nrf52_2.0.0-7.alpha_softdevice, the programme started but if I...
Hi
We are developing software for the nRF51 with Keil under VirtualBox. Previously we used the PCA10000 dongle with the Master Emulator and MCP without issue. Now, with...
We are using nRF51822 for our products.
We want to know the min value of "Receiver sensitivity" when we use this chip for BLE.
The Datasheet says "Receiver sensitivity...
Dear
The BLE Multi-link example (ble_app_multilink_central and ble_app_multilink_peripheral)
shows how one central device can connect to multiple peripheral devices. ...
Hi Friends,
- kit dev NF52840-DK
- IDE : segger studio IDE
- SDK nRF52 16.0.0
I want to port the nfc_writable_ndef_msg NFC example to freeRTOS.
I use the NFC Tools...
I'm learning that there are issues with the early "engineering versions" of the nRF52840, identified with QIAAAA marking.
Apparently the SPI3 BUS is not fully supported...
Hi,
After some strange behaviour of the DAC4716 chip, I want to try and reset it. The datasheet describes a way to do so over i2c using a specific bit stream. How can this...
I am having a N20 Micro Gear Motor with Encoder, I want to read data of c1 and c2 using GPIO pins. Any specificAPI, method or suggestion for this?
I am using nRF5340 along...
We have an application running on an nRF9160 development board (shortly to be ported to a production board), which listens on a serial link for sensor data, which is then...
Hello,
For network testing, I would like to use the Modem Shell App sample with the Thingy:91.
As suggested in the overlay file, I can disable some features, so the Build...
Hello,
I am attempting to use my nRF52810 (testing with the nRF52 DK) to generate square waves using PWM. Ideally, these square waves would operate at 8 or 16Mhz. So far...
Hi,
When will Nordic Connect SDK 2.1.0 be available? When have Nordic qualified SDK 2.1.0 and when is QDID number available (Host and Controller)?
We are running Zephyr...
Hi,
I am using the sensor_server example to develop our application on top of it. The problem I am facing is that, the model publication state (publish address and publish...
Hi,
I am using sensor server model to build our application on top of it. We want to save juice in the battery as much as possible. In order to that, I must disable bluetooth...
Hi, I'm developing a device based on nrf52840 and SDK for Thread and Zigbee 3.2.0.
I would like to send Route Record command to the coordinator to be able to see the actual...
Hello! We are trying to sign our data using ECDSA ( https://developer.nordicsemi.com/nRF_Connect_SDK/doc/latest/nrf/samples/crypto/ecdsa/README.html ) , so we can send our...
Hi,
as mentioned in a previous ticket I'm developing a successor to one of our products. One important feature is that we can change pin functions anytime. (output, input...
Hello all, I have a nrf52820 SoC with which I would like to do a DFU. When I flash softdevice, application and bootloader together with bootloader settings, the bootloader...
Hi,
We are developing the nRF52833 DK with NCS v2.00.
We are building a device that transmits various measured values from sensors every second for multiple hours (around...
